GB/T 28485-2012 PDF English
US$70.00 · In stock · Download in 9 secondsGB/T 28485-2012: Coated adornment -- Detection of nickel release -- Method for simulation of wear and corrosion Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 28485-2012 | English | 70 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Coated adornment -- Detection of nickel release -- Method for simulation of wear and corrosion
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 28485-2012
GB/T 28485-2012: Coated adornment -- Detection of nickel release -- Method for simulation of wear and corrosion
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT28485-2012
GB
ICS 39.060
Y 88
NATIONAL STANDARD
OF THE PEOPLE'S REPUBLIC OF CHINA
Coated Adornment - Detection of Nickel
Release - Method for Simulation of Wear
and Corrosion
Issued on: JUNE 29, 2012
Implemented on: NOVEMBER 01, 2012
Jointly Issued by. General Administration of Quality Supervision, Inspection
and Quarantine of the People's Republic of China;
Standardization Administration of the People's Republic of
China.
Table of Contents
Foreword... 3
1 Scope... 4
2 Normative References... 4
3 Principle... 4
4 Reagents and Materials... 4
5 Procedure... 6
6 Test Report... 8
Appendix A... 9
Appendix B... 10
Appendix C... 11
Foreword
This standard was drafted according to the rules specified in GB/T 1.1-2009.
This standard uses redrafting method to modify and adopt EN 12472.2005+A1.2009 "Method
for the Simulation of Wear and Corrosion for the Detection of Nickel Release from Coated
Samples" (English version).
Compared with EN 12472.2005+A1.2009, there are some adjustments in the structure of this
standard. The comparison of clause numbers of this standard and EN 12472.2005+A1.2009 is
listed in Appendix A.
The technical different clauses between this standard and EN 12472.2005+A1.2009 are
indicated by a single vertical line to the page margin. Appendix B provides the corresponding
technical differences.
Attention is drawn to the possibility that some of the elements of this document may be
subject to patent rights. The issuance organization shall not be held responsible for identifying
any or all such patent rights.
This standard was proposed by the China National Light Industry Council.
This standard shall be under the jurisdiction of the National Ornaments Technical Committee
for Standardization (SAC/TC 256).
Drafting organizations of this standard. National Jewelry Quality Supervision and Inspection
Center, Guangdong Entry-Exit Inspection and Quarantine Bureau, Inspection and Quarantine
Technology Center, Shandong Entry-Exit Inspection and Quarantine Bureau, Inspection and
Quarantine Technology Center, and Beijing Jewellery Quality Supervision and Inspection
Center.
Chief drafting staffs of this standard. Li Suqing, Li Yuou, Huang Lina, Liu Chonghua, Xing
Li, Gao Xuhui, and Li Wujun.
Coated Adornment - Detection of Nickel Release -
Method for Simulation of Wear and Corrosion
1 Scope
This standard specifies the method of pre-adopted wear and corrosion, in order to measure the
nickel release from non-nickel coating adornment.
This standard is applicable to non-nickel coating adornment that contacts with the skin in
long-term.
2 Normative References
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendment) applies.
GB/T 19719 Jewellery - Determination of the Release of Nickel - Method of Spectrometry
3 Principle
The sample to be tested are exposed to a corrosive environment, then ir is placed into a barrel
together with a wear-medium. The barrel is rotated so as the test sample is worn by the
wear-medium. The sample is then tested for nickel release in accordance with GB/T 19719.
4 Reagents and Materials
Except specially indicated, all reagents and materials that may contact with samples shall not
contain nickel. And all reagents shall be analytical grade or better grade.
4.1 Corrosion
4.1.1 Container
Container with a lid and with a device to make the test sample to be sudpendable. All parts
shall be made of inert material (e.g. glass or plastic).
4.1.2 Corrosive medium
Dissolve 50g of DL-lactic acid (purity >85%) and 100g of sodium chloride into 1000ml of
de-ionized water.
Appendix C
(Informative)
Examples of How to Attach Different Types of Samples
C.1 General
A retaining assembly is used to mount the test samples. This is inserted into the hexagonal
drum.
Materials which have been found suitable for fixing test samples in the retaining assembly are
silicone rubber sheet, silicone rubber straps, and nylon lines of different dimensions.
C.2 Attachment of samples with only one side in contact with the skin
Samples having one surface that can come into prolonged contact with the skin, and another
surface that is less likely to come into prolonged contact with the skin, should be mounted so
that they are fixed and cannot move inside the barrel. Examples are spectacle frames and
some watch straps. The test samples should be fixed so that they are positioned with the
surface that can come into contact with the skin turned towards the rotation axis, which is the
centre of the barrel, and with the other surface turned towards the wall of the barrel. If the
samples are relatively long, for example, spectacles or watch straps, then their long axis
should, if possible, be fitted parallel to the barrel axis. Samples for wear should be positioned
between 10mm and 30mm from the barrel walls.
C.3 Spectacle frames
GB/T 14214 (ISO 12870.2004, MOD) gives details on which parts of spectacle frames should
be tested.
The assembly consists of a threaded rod which carries three metal hexagonal plates - see
Figure C.1.The end plate (A) is drilled part way through with holes of nominal diameter 1.5
mm, or as appropriate, to take the ends of the tips of the sides. The next plate (B - see Figure
C.2) is perforated with holes of nominal diameter 5mm, or as appropriate, to take the joint
ends of the sides, together with an aperture of 40 mm nominal diameter to act as a filling hole
for the abrasive mixture. A silicone rubber sheet with small holes matching the position of
those in plate (B) holds the sides firmly to prevent them from rotating in the assembly. A
second, un-perforated, silicone sheet presses the sides into plate (A). The final plate (C) is
un-drilled apart from the hole for the threaded rod. A threaded nut on the inside of the last two
plates holds them the required distance from plate A, while a second nut on the outside
clamps the assembly together. The sides should be mounted with the inside surface towards
the axis of the assembly.
Spectacle fronts should be mounted so that one of the lugs is inserted into the holes in plate
(B). It may be necessary to straighten the lug or to twist the rim immediately either side of the
Figure C.3 Examples of How to Fix Different Types of Samples in Retaining Assembly
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 28485-2012 be delivered?Answer: The full copy PDF of English version of GB/T 28485-2012 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 28485-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 28485-2012_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 28485-2012 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 28485-2012?A step-by-step guide to download PDF of GB/T 28485-2012_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 28485-2012".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|