GB/T 22030-2013 (GBT22030-2013)

Standard ID	Contents [version]	USD	STEP2	[PDF] delivered in	Standard Title (Description)	Related Standard	Status	PDF
GB/T 22030-2013	English	319	Add to Cart	3 days [Need to translate]	Blend stocks of ethanol gasoline for motor vehicles	GB/T 22030-2013	Obsolete	GB/T 22030-2013

GB/T 22030-2013
Blendstocks of ethanol gasoline for motor vehicles
ICS 75.160.20
E31
National Standards of People's Republic of China
Replacing GB/T 22030-2008
Vehicle ethanol gasoline blending component oil
Issued on. 2013-10-10
2014-01-01 implementation
Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China
Standardization Administration of China released
Foreword
This standard was drafted in accordance with GB/T 1.1-2009 given rules.
This standard replaces GB/T 22030-2008 "vehicle ethanol gasoline blending components of oil."
This standard compared with GB/T 22030-2008, the main technical differences are as follows.
--- Remove the original standard preface "Since the implementation of this standard, the technical requirements specified in Table 2 of the transition period to December 2009
31 ";
--- Increased content Home "Warnings" content;
--- Remove the scope of "technical requirements for compliance with this standard in Table 1 apply to products formulated to meet the first phase Ⅱ of vehicle emissions to
The vehicle ethanol gasoline demand, in line with the technical requirements of this standard apply to Table 2 products formulated to meet China stage Ⅲ vehicle exhaust
Put the required vehicle ethanol gasoline. "(See Chapter 1, Chapter 1, 2008);
--- Added "vehicle ethanol gasoline additive blending components used in the oil should be no proven harmful effects, according to recommendation of appropriate use
Amount. Vehicle ethanol gasoline blending component oil should not contain any additives and pollution can cause the car can not run normally
Thereof. "(See 5.1);
--- Delete the original standard of Table 1, revised the original criteria in Table 2;
--- Added "unwashed gum" index limits (see table version 1,2008 Table 2);
--- Vapor pressure indicators from "November 1 to April 30 is not greater than 81kPa; May 1 to October 31 is not greater than 65kPa"
Amended to read "1 November to 30 April 37kPa ~ 78kPa; May 1 to October 31 35kPa ~ 61kPa"
(See table version 1,2008 Table 2);
--- Sulfur content indicators from "not more than 0.016% (mass fraction)" was changed to "not more than 50mg/kg" (see table version 1,2008 Table 2);
--- The olefin content index from "not more than 33% (volume fraction)" was changed to "not more than 30% (volume fraction)" (see table 1,2008
Version Table 2) ";
--- The aromatic content index from "not more than 44% (volume fraction)" was changed to "not more than 43% (volume fraction)" (see table 1,2008
Version Table 2)
--- The manganese content index from "not more than 0.016g/L" was changed to "not more than 0.008g/L" (see table version 1,2008 Table 2);
--- Original table 2 footnote g amended as follows. "For the 97 ethanol gasoline blending components oil, olefins, aromatics total content control
Under the same premise, the allowable maximum aromatics content (volume fraction) of 45%. Allows the use of NB/SH/T 0741 were
Determination, when there is objection to GB/T 11132 measurement results shall prevail. "(Table Version 1,2008 Table 2);
--- Increased Chapter 8, "Security" (see Chapter 8).
This standard by the National Standardization Technical Committee on products and lubricant oil (SAC/TC280) proposed.
This standard by the National Standardization Technical Committee of petroleum products lubricants oil and lubricants and fuels Technical Committee (SAC/TC280 /
SC1) centralized.
This standard was drafted. China Research Institute of Petroleum Corp. Petrochemical, China Petroleum & Chemical Corporation,
China National Petroleum Corporation.
The main drafters of this standard. Ni Bei, Zhang Baosheng, Zhang Yan.
This standard was first published in 2008, this is the first revision.
Vehicle ethanol gasoline blending component oil
Warning. If you do not observe proper precautions, this standard may be relevant to your product in the production, transportation, handling, storage and use of the process
Dangerous. This standard is not intended to present all of the safety issues related to the product recommendations. Before using this standard has the responsibility to build
And establish appropriate safety pre