GB/T 16507.4-2022_English: PDF (GBT16507.4-2022)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Related Standard | Status | PDF |
| GB/T 16507.4-2022 | English | 1099 |
Add to Cart
|
7 days
|
Water-tube boilers - Part 4: Strength calculation of pressure parts
|
GB/T 16507.4-2022
| Valid |
GB/T 16507.4-2022
|
| Standard ID | GB/T 16507.4-2022 (GB/T16507.4-2022) | | Description (Translated English) | Water-tube boilers - Part 4: Strength calculation of pressure parts | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J98 | | Classification of International Standard | 27.060.30 | | Word Count Estimation | 55,556 | | Date of Issue | 2022-03-09 | | Date of Implementation | 2022-10-01 | | Drafting Organization | Shanghai Power Generation Equipment Design and Research Institute Co., Ltd., Harbin Boiler Factory Co., Ltd., Dongfang Electric Group Dongfang Boiler Co., Ltd., Shanghai Boiler Factory Co., Ltd., Beijing Babcock Wilcox Co., Ltd., Wuhan Boiler Co., Ltd. Co., Ltd., Wuxi Huaguang Environmental Protection Energy Group Co., Ltd., Hangzhou Boiler Group Co., Ltd., Harbin Electric Power Generation Equipment National Engineering Research Center Co., Ltd., Sichuan Chuanguo Boiler Co., Ltd., Jinan Boiler Group Co., Ltd., Xi'an Thermal Engineering Research Institute Co., Ltd., China Special Equipment Testing Institute, Jianglian Heavy Industry Group Co., Ltd. | | Administrative Organization | National Technical Committee for Standardization of Boilers and Pressure Vessels (SAC/TC 262) | | Proposing organization | National Technical Committee for Standardization of Boilers and Pressure Vessels (SAC/TC 262) | | Issuing agency(ies) | State Administration for Market Regulation, National Standardization Administration | GB/T 16507.4-2022
Water-tube boilers - Part 4.Strength calculation of pressure parts
ICS 27.060.30
CCSJ98
National Standards of People's Republic of China
Replaces GB/T 16507.4-2013
water tube boiler
Part 4.Calculation of Strength of Compressed Components
Published on 2022-03-09
2022-10-01 Implementation
State Administration for Market Regulation
Released by the National Standardization Administration
directory
Preface I
Introduction III
1 Scope 1
2 Normative references 1
3 Terms and Definitions 1
4 Basic requirements 2
5 Allowable stress 3
6 Calculate the wall temperature 3
7 Calculate pressure 5
8 Attenuation factor 6
9 Component thickness 10
10 Calculate thickness 11
11 Opening reinforcement 17
12 Thickness addition 22
13 Maximum allowable pressure 23
14 Additional stress check 25
15 Structural limitations and requirements 26
Appendix A (Normative) Calculation of Low Cycle Fatigue Life of Drum 33
Appendix B (normative) Test and Finite Element Analysis Verification Method for Determining the Maximum Allowable Working Pressure of Components 40
Appendix C (normative) Design additional pressure (Δpa) value 44
Appendix D (informative) The value of the additional thickness of the process is 45
Appendix E (Informative) Approximate Algorithm for Flexural Section Modulus (Wx1) of Opening Weakened Sections 47
Reference 49
foreword
This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules of Standardization Documents"
drafted.
This document is Part 4 of GB/T 16507 "Water Tube Boiler". GB/T 16507 has released the following parts.
--- Part 1.General;
--- Part 2.Materials;
--- Part 3.Structural design;
--- Part 4.Strength calculation of pressure components;
--- Part 5.Manufacturing;
--- Part 6.Inspection, testing and acceptance;
--- Part 7.Safety accessories and instruments;
--- Part 8.Installation and operation.
This document replaces GB/T 16507.4-2013 "Water Tube Boiler Part 4.Strength Calculation of Compressed Components", and GB/T 16507.4-
Compared with.2013, except for structural adjustment and editorial changes, the main technical changes are as follows.
--- Changed the range of pressure components, increased the start (soda) separator (see Chapter 1, Chapter 1 of the.2013 edition);
--- Changed and added the terms and definitions used in this section (see Chapter 3, Chapter 3 of the.2013 edition);
--- Changed the scope of use for the calculation of low cycle fatigue life, allowing the start (soda-water) separator to be used as a reference (see 4.2,.2013 edition of
4.2);
---Increase the allowable stress value of materials between adjacent temperatures to be determined by arithmetic interpolation and the allowable stress value of materials should be rounded off after the decimal point
the numerical provisions (see 5.2.1);
--- Changed the relevant provisions for determining the calculation pressure (see 7.3, 7.3 of the.2013 edition);
--- Increase the calculation provisions for the reinforcement of convex head openings (see 10.3.8, 11.2, 11.3.6, 11.5.6, 11.5.8);
--- Added the calculation method for convex heads under external pressure (see 10.3.9);
--- Increased the scope of application of the formula for calculating the thickness of elbows or elbows and arc-shaped header cylinders (see 10.6.5);
--- Increased the weld height specification for the opening reinforced nozzle (see 11.4.2, 11.5.8);
--- Changed the size requirements (L1, hmin, r), specification range, and structural requirements of the tee (see 15.3.12~15.3.28,.2013 edition
16.3.18~16.3.37);
--- Delete the provisions of the minimum radial residual thickness of the incision part of the sealing surface of the convex head manhole (see 16.3.11 of the.2013 edition);
--- Changed the content of "Calculation of low cycle fatigue life of boiler drum" (see Appendix A, Appendix A of the.2013 edition);
--- Changed the relevant content of the verification method for determining the maximum allowable working pressure of components (see Appendix B, Cha
|