GB/T 16507.1-2013 (GBT16507.1-2013)

Standard ID	Contents [version]	USD	STEP2	[PDF] delivered in	Standard Title (Description)	Related Standard	Status	PDF
GB/T 16507.1-2013	English	839	Add to Cart	4 days [Need to translate]	Water-tube boilers -- Part 1: General requirement	GB/T 16507.1-2013	Obsolete	GB/T 16507.1-2013

GB/T 16507.1-2013
Water-tube boilers Part 1. General requirement
ICS 27.060.30
J98
National Standards of People's Republic of China
Partially replace GB/T 16507-1996
Water tube boiler
Part 1. General
Part 1. Generalrequirement
Issued on. 2013-12-31
2014-07-01 implementation
Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China
Standardization Administration of China released
Table of Contents
Preface Ⅰ
Introduction Ⅱ
1 Scope 1
2 Normative references 1
3 Terms and Symbols 2
4 Eligibility and Liability 4
5 boiler scoping 5
6 General requirements 8
Appendix A (normative) Declaration of Conformity 15
Foreword
GB/T 16507 "Water Boiler" is divided into eight sections.
--- Part 1. General;
--- Part 2. Materials;
--- Part 3. Design;
--- Part 4. Strength calculation of pressure parts;
--- Part 5. Manufacturing;
--- Part 6. Inspection, testing and acceptance;
--- Part 7. Safety Accessories and instrumentation;
--- Part 8. Install and run.
This section GB/T Part of 116,507.
This section drafted in accordance with GB/T 1.1-2009 given rules.
This portion instead of GB/T 16507-1996, compared with the GB/T 16507-1996, the main technical changes are as follows.
--- Water tube boilers and shell boilers is divided into two separate standards, water boiler GB/T 16507, shell boilers as
GB/T 16508;
--- Water tube boiler standard is divided into general principles, materials, structural design, strength calculation of pressure parts, fabrication, inspection, testing and acceptance, security
8 annex and instrumentation, installation and operation, etc;
--- Provides manufacturing units, the use of units, qualifications and responsibilities of units installed;
--- Defines the scope of the boiler;
--- Increase the value specified steel bolts material allowable stress;
--- Increasing the installation and operation of part of the requirements;
--- Increased energy conservation and environmental protection requirements.
This part of the National boiler pressure vessel Standardization Technical Committee (SAC/TC262) and focal points.
This section is responsible for drafting unit. Shanghai Power Equipment Research Institute.
This section involved in the drafting unit. Shanghai Boiler Works, Ltd., Harbin Boiler Factory Co., Ltd., Dongfang Electric Group, Dongfang Boiler
Co., Ltd., Beijing Babcock & Wilcox Co., Ltd., Wuhan Boiler Co., Ltd., Hangzhou Boiler Group Co. Shares
The company, Wuxi Huaguang Boiler Co., Ltd., China Electricity Council, Shanghai Industrial Boiler Research Institute.
The main drafters of this section. Fossil Fuel, Zhengguo Yao, Zhang Rui, An Qi Fang, Xu Yujun, who will be strong, Kong Bohan, Xiaohui Fang, Hou Xiaodong, left Caixia,
Zhu Zhiqiang, Chen Xiubin money Fenghua, Lu Xiang, Xiao Zhonghua.
This part of the standard replaces the previous editions are.
--- GB/T 16507-1996.
introduction
GB/T 16507 is the boiler pressure vessel Standardization Technical Committee (hereinafter referred to as "the Committee") is responsible for the development and centralized boiler
One common technical standards, to regulate the construction or use in China's boiler design, manufacture, testing, inspection and installation of related technologies
Claim.
Since this standard is not necessary, it is impossible to include within the scope of the boiler construction and installation of all the technical details, therefore, to meet
The basic premise of safety requirements and regulations stipulated, this standard should not be prohibited without technical content specifically mentioned.
This standard does not limit the actual engineering design and construction using advanced technology and methods, but engineers using advanced technology and methods
We should be able to make reliable judgments, to ensure that it meets this standard.
This standard neither requires nor prohibits designers use computer program analysis or design of the boiler, but the use of a computer program into
Line analysis or design, in addition shall meet the requirements of this standard, it must also