GB/T 13667.3-2013_English: PDF (GB/T13667.3-2013)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 13667.3-2013 | English | 299 |
Add to Cart
|
3 days [Need to translate]
|
Steel book shelves -- Part 3: Manual dense bookshelf
| Valid |
GB/T 13667.3-2013
|
| GB/T 13667.3-2003 | English | 279 |
Add to Cart
|
3 days [Need to translate]
|
Technical specification for compact handbook shelves
| Obsolete |
GB/T 13667.3-2003
|
| GB/T 13667.3-1992 | English | 239 |
Add to Cart
|
2 days [Need to translate]
|
Technical specification of compact hand book-shelves
| Obsolete |
GB/T 13667.3-1992
|
| Standard ID | GB/T 13667.3-2013 (GB/T13667.3-2013) | | Description (Translated English) | Steel book shelves. Part 3: Manual dense bookshelf | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | Y81 | | Classification of International Standard | 97.140 | | Word Count Estimation | 13,176 | | Older Standard (superseded by this standard) | GB/T 13667.3-2003 | | Quoted Standard | GB/T 1720; GB/T 1730; GB/T 1732; GB/T 9969; GB/T 10357.4; GB/T 13666; GB/T 13667.1-2003 | | Drafting Organization | National Office Supplies Equipment Quality Supervision and Inspection Center | | Administrative Organization | National Standardization Technical Committee furniture | | Regulation (derived from) | National Standards Bulletin 2013 No. 27 | | Proposing organization | China Light Industry Association | | Issuing agency(ies) | General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China | | Summary | This standard specifies the manually intensive shelves terms and definitions, classification and nomenclature, requirements, test methods, inspection rules, marking, packaging, transportation and storage. This standard applies to manually intensive booksh | | Standard ID | GB/T 13667.3-2003 (GB/T13667.3-2003) | | Description (Translated English) | Technical specification for compact hand book shelves | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | Y81 | | Classification of International Standard | 97.140 | | Word Count Estimation | 7,797 | | Date of Issue | 2003-11-27 | | Date of Implementation | 2004-05-01 | | Older Standard (superseded by this standard) | GB/T 13667.3-1992 | | Quoted Standard | GB/T 191; GB 9969.1 | | Drafting Organization | Shanghai Baoshan District Story Books Equipment Factory | | Administrative Organization | National Office Supplies Equipment Quality Supervision and Inspection Center | | Regulation (derived from) | Chinese national standard approved by the announcement of 2004 (No. 63 overall) 1; National Standards Bulletin 2013 No. 27 | | Proposing organization | China Light Industry Federation | | Issuing agency(ies) | General Administration of Quality Supervision, Inspection and Quarantine of the People Republic of China | | Summary | This standard specifies: manual intensive shelves terms and definitions, classification and nomenclature, materials and structures, requirements, test methods, inspection rules, marking, packaging, transport and storage. This standard applies to: Manually intensive bookshelf. | | Standard ID | GB/T 13667.3-1992 (GB/T13667.3-1992) | | Description (Translated English) | Technical specification of compact hand book-shelves | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | Y81 | | Classification of International Standard | 97.14 | | Word Count Estimation | 6,669 | | Date of Issue | 1992/9/4 | | Date of Implementation | 1993/8/1 | | Regulation (derived from) | Announcement of Newly Approved National Standards 2004 No. 1 (No. 63 overall) |
GB/T 13667.3-2013
Steel book shelves Part 3.. Manual dense bookshelf
ICS 97.140
Y81
National Standards of People's Republic of China
Replacing GB/T 13667.3-2003
Steel shelves - Part 3. Manually intensive Bookshelf
Issued on. 2013-12-31
2014-12-01 implementation
Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China
Standardization Administration of China released
Foreword
GB/T 13667 "steel shelves" is divided into four parts.
--- Part 1. Single, double column bookshelf;
--- Part 2. laminate type shelves;
--- Part 3. Manually intensive shelves;
--- Part 4. Electric intensive bookshelf.
This section GB/T Part of 313,667.
This section drafted in accordance with GB/T 1.1-2009 given rules.
This Part replaces GB/T 13667.3-2003 "Bookshelf manually intensive technical conditions." This portion of the GB/T 13667.3-2003 phase
Ratio, the main technical changes are as follows.
--- The term "standard frame" to "intensive shelves standard shelf Column", and modify the definition contents (see 32, 2003 version 3.2.);
--- Remove the material requirements (2003 version 5.1);
--- Delete the column, siding and other parts requirements (2003 version 6.1);
--- Deleted phosphate gloss requirements (2003 version 6.3);
--- Modify the assembly requirements (see 53, 2003 version 6.4.);
--- Modify the stability requirements (see 55, 2003 version 6.7.);
--- The "size test" to "assembly requirements determination," and modify the test methods (see 63, 2003 version 7.1.);
--- Modify the structural strength test method (see 66, 2003 version 7.7.);
--- Modify the inspection rules (see 7, 2003 edition of 8);
--- Modify the logo, packaging, transportation and storage (see 8, 2003 edition of 9).
Please note that some of the content of this document may involve patents. Release mechanism of the present document does not assume responsibility for the identification of these patents.
This part is proposed by the China National Light Industry Council.
This part of the furniture by the National Standardization Technical Committee (SAC/TC480) centralized.
This part mainly drafted by. National office supplies equipment for Quality Supervision and Inspection Center, Jiangxi Sunshine Safety Equipment Co., Ltd.
Participated in the drafting of this section. Jiangxi Jinhu Insurance Holdings Limited, Ningbo towards flat modern furniture Limited Jiang Xi Zhuoer gold
Genus Equipment Group Co., Ltd., Jiangxi offshore insurance Equipment Industry Group Co., Ltd., Ningbo million gold Modern Sheet Metal Co., Henan Huacheng
Office Furniture Co., Ltd. Hangzhou Wan Bao cabinet, metal furniture China Furniture Association Professional Committee.
The main drafters of this section. Zhang Hong, Deng Chao, Gu Qiang, Zheng Hong company, Zhang Jian, Xiong Shulin, Xu Yiping, Niejian Chun, such as bears love, Zhu Chunlei, Zhang Huan group,
Lu Qi, Yang Lei.
This part of the standard replaces the previous editions are.
--- GB/T 13667.3-1992, GB/T 13667.3-2003.
Steel shelves - Part 3. Manually intensive Bookshelf
1 Scope
This section GB/T 13667 specifies the manually intensive bookshelf terms and definitions, classification and nomenclature, requirements, test methods, inspection regulations
Then, signs, packaging, transportation and storage.
This section applies to bookshelf intensive manual.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 1720 film adhesion assay
GB/T 1730 Paints and varnishes - Pendulum damping test
GB/T 1732 Determination of impact resistance of film
GB/T 9969 General Instructions industrial products
GB/T 10357.4 furniture mechanical properties test - Part 4. Cabinet Stability
GB/T 13666 Books Supplies Equipment Model methodology
GB/T 13667.1-2003 steel shelves General technical conditions
3 Terms and Definitions
GB/T 13667.1-2003 and the following definition of terms and definitions are applicable to this document.
3.1
Manually intensive Bookshelf manualdensebookshelf
Can be achieved by shaking the handle to run on the rails, the movable frame columns and columns of the holder can be dispersed or set of bookshelves combination, the main
By the column, shelf, side panels, base beams, joystick, wheel, gear, guide rails and other component parts.
3.2
Bookshelf intensive standard frame listed standardshelfseriesofdensebookshelf
It consists of a main frame and sub-frame consisting of two columns of the movable frame used for the test.
3.3
The movable frame column activeshelfseries
You can run on the rails bookshelf column.
3.4
Holder column fixedshelfseries
With respect to the movable frame column, fixed position, Bookshelf column can not run.
4 Classification and Nomenclature
4.1 Naming
Naming and Model methodology products should comply with GB/T 13666 of.
4.2 Classification and dimensions
Classification and unit frame size of the product are shown in Table 1. Product structure is shown in Figure 1.
Table 1 Classification and unit frame size in millimeters
classification
size
Height H width B depth T
The movable frame columns 1900 to 2500, 400 to 600 900-1000
Column holder
Duplex 1900 ~ 2500900 ~ 1000400 ~ 600
Sided ~ 1900 ~ 1000200 ~ 2500900 300
Note. The special specification according to the contract.
5 Requirements
5.1 Appearance
5.1.1 the parts surface should be smooth, flat, there should be no sharp corners and projections.
5.1.2 welded shall be welded solid, smooth welding marks.
5.1.3 The surface of the coating should be smooth, uniform color, there should be no sagging, from grain, wrinkled skin, exposed at the end, flaking, scratches and other defects.
5.1.4 plating coating should be bright, exposed parts should not have burned, bubbles, pinholes, cracks, piebald, scratches and burrs.
5.2 surface coating physical and chemical properties
Physical and chemical properties of surface coating products comply with the requirements of Table 2.
Table 2 surface coating physical and chemical properties
Test item number requirements, test methods
1 Hardness ≥0.4 GB/T 1730
2 impact strength impact height 40cm, should not peel, crack, wrinkle GB/T 1732
3 adhesion level should not be less than 2 GB/T 1720
4 corrosion-resistant
Within 100h, viewed in the road outside the designated template solution on both sides of 3mm, there should be no bubbles
100h after, the model should be no check on both sides of 3mm outside the designated road rust, peeling, wrinkling, change
Loss of light and color phenomena
GB/T 13667.1-2003
In 7.3.3.7
5.5.3 Loading shelf level stability
According to GB/T 10357.4 provisions applied at the highest levels of tension 90N middle shelf unit shelf, keeping 1min, should frame body
Dumping.
5.6 Structural Strength
Standard frame listed at full static load, horizontal tensile testing along the X, Y-axis in both directions, the level of tension and full of static weight load
The Dutch and 1/15, the successive test 50 times, the test frame body can not dump the phenomenon occurs, the amount of tilt frame body after the test shall not exceed the total frame body
1% higher, each structural member should be no plastic deformation or other anomalies.
6 Test methods
6.1 Determination of appearance
Shall be visually measured under natural light or near natural light (such as 40W fluorescent lamp), line of sight is within 700mm.
6.2 Determination of surface coating physical and chemical properties
Conducted in accordance with Table 2.
6.3 Determination of assembly requirements
6.3.1 Dimensions deviation
Use accuracy not less than ± 0.6mm steel tape, steel ruler measurement unit rack height, width and depth, which measures the difference between the value and the nominal value
Is the appropriate limit deviations.
6.3.2 rail deviation
6.3.2.1 single rail straightness
Using precision grade is not less than 2 square feet of 1000mm and a feeler, feet flat against the side rails, measured with a feeler largest room
Gap is straightness per meter of a single rail.
6.3.2.2 The deviation from a single rail
With steel ruler and accuracy not less than ± 0.5mm/5m level measurement, level meter to make adjustments on the horizontal side rails, water
Flat line as a baseline to measure the distance to the rail multipoint baseline, within 1m of any difference between maximum and minimum values \u200b\u200bfor the single rail level deviation.
6.3.2.3 adjacent parallel deviation between two rail width
Wherein a guide to baseline, measured on another rail from baseline to multi-point, any difference between the maximum and minimum 1m within the
Parallel deviation between two rail width.
6.3.2.4 two adjacent horizontal rail height deviation
With steel ruler and accuracy not less than ± 0.5mm/5m level measurement. Will be adjusted to a level of two horizontal rails
Above the horizontal line as a baseline to measure the two opposing points to the guide rail from baseline, the absolute value of the difference between the height deviation, whichever
A maximum of two guide rails height deviation.
6.3.2.5 rail height difference between the abutment
With flat feet and a feeler gauge. The flat feet against the rail butt joint, with a feeler measuring the maximum gap is the difference between high and low rail butt joint.
6.3.3 column and the bottom of the vertical beam
With a feeler Square top with the column gap δ '.
Column and the bottom of the vertical beam according to equation (1) calculations. Is shown in Figure 2.
δ =
H · δ '
(1)
Where.
Degree δ --- vertical column and the bottom of the beam, in millimeters (mm);
H --- high column, in millimeters (mm);
δ '--- Square and the gap to the top of the column, in millimeters (mm);
h --- Square height in millimeters (mm).
figure 2
6.3.4 degree of difference
The use of flat-foot steel ruler and measured.
6.3.5 gap
6.3.5.1 The side panels and backs the abutment gap
Using a feeler gauge measurements.
6.3.5.2 Dust door gap
Using a feeler gauge measurements.
6.3.6 adjustability
Visual and manual checks.
6.3.7 Interchangeability
Were randomly selected from the same types of specifications three shelves and three hanging panels are interchangeable for any position.
6.3.8 Performance actuator
Visual and manual checks.
6.3.9 Anti-dumping
Visual and manual checks.
6.3.10 Limit
Visual and manual checks.
6.3.11 fixed
Visual and manual checks.
6.4 Load Performance Measurement
6.4.1 Determination of static load shelf
According to GB/T 13667.1-2003 7.4 requirements, single-sided shelves on each shelf evenly distributed static load 400N, each double-sided shelves
On a shelf uniformly distributed static load 800N, quality and accuracy of the load rating of ± 1%.
6.4.2 full static load measurement
On each shelf plus uniform static load, load see GB/T 13667.1-2003 Table 8 of the load mass accuracy rating of ± 1%.
6.4.3 Load measurement run
6.4.3.1 shake the handle at full static load, so that the frame body running back and forth on the rails again, check the gear lever and the frame body processes run.
6.4.3.2 The hanging dynamometer crank handle on the movement of the handle along the tangential direction, hand dynamometer drive handle is turned, make a note of the standard rack column
Starting dynamometer readings is cranking power and observe the operation. Test the handle clockwise and counterclockwise each do a test
The result is the average of two determinations.
6.5 Determination of stability
6.5.1 dust load stability when the door is open
Performed according to GB/T 10357.4 requirements.
6.5.2 dust load stability when the door is opened
Performed according to GB/T 10357.4 requirements.
6.5.3 Loading shelf level stability
Performed according to GB/T 10357.4 requirements.
6.6 Determination of structural strength
6.6.1 Test Equipment
Structural strength test equipment should meet the following requirements.
a) structural strength testing machine. accuracy of the rated load power ± 5% (the structure is shown in Figure 3);
b) rangefinder. Range 0mm ~ 150mm, accuracy not less than ± 0.5%;
c) the weighing device. Range 0kg ~ 5000kg, accuracy not less than ± 1%.
Table 4 Project classification and classification test
Terms of Reference technical inspection items
Item Category
Basic general
Inspection classification
Settlement type test test
1 5.1 Appearance - √ √ √
2 5.2 Surface coating physical and chemical properties √ - - √
3 5.3 assembly requirements
Table 3 1 ~ 7 √ √ √
Table 3 8 ~ 10 √ - √ √
4 5.4.1 shelf static load √ - - √
5 Full 5.4.2 static load √ - √ √
6 5.4.3 Load operation √ - √ √
7 5.5.1 - 5.5.3 Stability √ - √ √
8 5.6 structural strength √ - - √
Note. delivery inspection items can be adjusted according to customer demand.
7.2.3 determination principle
Basic projects are qualified and general project failed no more than three items, the product is judged as qualified, otherwise unqualified.
7.3 Type inspection
7.3.1 type inspection timing
When one of the following conditions, type of inspection should be carried out.
a) new products or old products to the plant production trial to identify stereotypes;
B) after the official production, such as structure, materials, technology has drastically changed, it may affect product quality and performance;
c) Normal production, after regular or accumulate a certain yield, at least once a year type of inspection;
d) one year after the product discontinuation, resume production;
e) Settlement test results are quite different when the last type inspection;
f) Other types of inspection when required.
7.3.2 Type inspection items and sampling methods
Type test items and the order will be as defined in Table 4. The same group in a test cycle, the same specifications of the product Randomly
Take several parts assembled into a set of manual-intensive standard rack shelves and a column, and then do 5.1 in the set manually intensive bookshelf, Table 3 rails
Progressive deviation, number of items 3,8 to 10 5.5.1,5.5.2 project activity equipped with dust-proof door frame columns, other items in the standard rack
Test the column.
7.3.3 determination principle
Basic projects are qualified and general project failed no more than three items, the product is judged as qualified, otherwise unqualified.
......
|