GB 31604.22-2016_English: PDF (GB31604.22-2016)
Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
GB 31604.22-2016 | English | 70 |
Add to Cart
|
0--9 seconds. Auto-delivery
|
Method for analysis of hygienic standard of products of foamed polystyrene for food packaging
| Valid |
GB 31604.22-2016
|
Preview PDF: GB 31604.22-2016
Standard ID | GB 31604.22-2016 (GB31604.22-2016) | Description (Translated English) | Method for analysis of hygienic standard of products of foamed polystyrene for food packaging | Sector / Industry | National Standard | Classification of Chinese Standard | X09 | Word Count Estimation | 6,671 | Date of Issue | 2016-10-19 | Date of Implementation | 2017-04-19 | Older Standard (superseded by this standard) | GB/T 5009.100-2003 | Regulation (derived from) | State Health and Family Planning Commission Notice No.1516 of 2016 |
GB 31604.22-2016
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
National Food Safety Standard - Food Contact Materials
and Articles - Determination of Dichlorodifluoromethane
in Products of Foamed Polystyrene
ISSUED ON. OCTOBER 19, 2016
IMPLEMENTED ON. APRIL 19, 2017
Issued by. National Health and Family Planning Commission of the PRC
Table of Contents
Foreword . 3
1 Scope .. 4
2 Principles . 4
3 Reagents and materials .. 4
4 Instruments and equipment . 5
5 Analytical procedures . 5
6 Analysis results expression . 6
7 Precision. 7
8 Others . 7
Appendix A Gas chromatogram of dichlorodifluoromethane standard solution 8
National Food Safety Standard - Food Contact Materials
and Articles - Determination of Dichlorodifluoromethane
in Products of Foamed Polystyrene
1 Scope
This Standard specifies the method for determination of
dichlorodifluoromethane in products of foamed polystyrene.
This Standard applies to the determination of dichlorodifluoromethane in
products of foamed polystyrene.
2 Principles
According to relevant gas law, PLACE the sample in a sealed equilibration flask;
and USE a solvent to dissolve. At a certain temperature,
dichlorodifluoromethane diffuses. When it reaches an equilibration, TAKE the
head space gas and INJECT it into gas chromatograph for determination.
3 Reagents and materials
Unless otherwise stated, the reagents used in this method are analytically pure.
The water is the Grade II water specified in GB/T 6682.
3.1 Reagents
3.1.1 N, N-dimethylacetamide (C4H9NO). chromatographically pure.
3.2 Standard
Dichlorodifluoromethane (CCl2F2) (CAS Number. 75-71-8). The purity>99%.
3.3 Preparation of standard solutions
3.3.1 Standard stock solution of dichlorodifluoromethane (100 μg/mL).
Accurately WEIGH 1 mg (accurate to 0.01 mg) of dimethylacetamide standard
in a 10 mL brown volumetric flask; USE N, N-dimethylacetamide to dissolve and
dilute to volume; and MIX well. At 4 °C, STORE it for 1 year.
c) Inlet temperature. 250 °C;
d) Detector temperature. 300 °C;
e) Carrier gas. nitrogen; the purity is greater than or equal to 99.999%.
Constant current mode; flow rate. 1.0 mL/min;
f) Injection volume. 1.0 mL, split injection; the split ratio is 20.1;
g) Make-up gas. nitrogen, 60 mL/min.
5.3 Making of standard curve
ADD 3 mL of N, N-dimethylacetamide in each of 5 equilibration flasks; CAP the
plugs; USE a microsyringe to take 0 μL, 3 μL, 15 μL, 30 μL, 150 μL, 300 μL of
standard working solution of dichlorodifluoromethane (1 μg/mL) and INJECT
into the flasks through rubber plug; gently SHAKE well and PUT in a constant
temperature water bath at 65 °C to equilibrate for 15 min. The standard curve
concentrations are 0 ng/mL, 1 ng/mL, 5 ng/mL, 10 ng/mL, 50 ng/mL,100 ng/mL.
Respectively TAKE 1 mL of the head space gas and INJECT into gas
chromatograph; TAKE the dichlorodifluoromethane content as the abscissa;
TAKE the peak area as the ordinate and DRAW standard curve. The gas
chromatogram of dichlorodifluoromethane standard solution is as shown in
Figure A.1.
5.4 Determination of sample solution
Manually or automatically INJECT the head space gas, which contains 1 mL of
the sample, into gas chromatograph to determine; and OBTAIN the peak area.
According to the standard curve, OBTAIN the content of
dichlorodifluoromethane in the sample solution. At the same time, CARRY out
blank test.
6 Analysis results expression
The content of dichlorodifluoromethane in the sample is calculated according
to the equation (1).
Where.
X - The content of dichlorodifluoromethane in the sample, in micrograms per
kilogram (mg/kg);
......
|