FZ/T 01034-2008 (FZT 01034-2008)

Standard ID	Contents [version]	USD	STEP2	[PDF] delivered in	Standard Title (Description)	Related Standard	Status	PDF
FZ/T 01034-2008	English	189	Add to Cart	3 days	Textiles. Test methods of the tensile elasticity for woven fabrics	FZ/T 01034-2008	Valid	FZ/T 01034-2008

FZ/T 01034-2008
Textiles.Test methods of the tensile elasticity for woven fabrics
ICS 59.080.30
W04
People's Republic of China textile industry standards
Replacing FZ/T 01034-1993
Standard Test Method for Elastic Textiles - Woven fabrics stretch
Posted 2008-03-12
2008-09-01 implementation
National Development and Reform Commission, People's Republic of China released
Foreword
This standard is the FZ/T 01034-1993 "tensile elastic woven fabric test method" amendments. Compared with the FZ/T 01034-1993,
The main changes are as follows.
1) the integration of FZ/T 01062-1999 "Standard Test Method for Elastic tensile elastic woven fabrics" (original ZB W04010-1989) section
Min content.
2) expand the scope of application, including elastic and inelastic woven fabrics.
3) an increase in Chapter 3.
4) Fabric Tensile tester specifically for the CRE type tensile strength tester.
5) "sample" and "Sample Preparation" original two chapters into the "sampling" chapter.
6) the original "instruments of correction," the incorporated "step" within a chapter, and increases the tensile speed of 100mm/min a file.
7) increase the pre-tension slack holding method and stretch fabrics.
8) anyone values or constant elongation value to be determined or recommended value according to product requirements or mutual agreement.
9) retention time drawing or stretching parked time and recovery time to be determined or recommended value is determined based on product requirements or mutual agreement.
The original standard position extending the parking time and response time of 1min 3min to the recommended value.
10) repeatedly stretching cycles to determine the value determined in accordance with the product or recommended requirements or mutual agreement.
11) increased the elongation anyone, elongation force set, stress relaxation rate, concentration of plastic deformation and elastic recovery rate measurement project.
Instead of the standard FZ/T 01034-1993 from the implementation date.
The standard proposed by China Textile Industry Association.
This standard by the National Standardization Technical Committee based textile branch (SAC/TC209/SC1) centralized.
This standard was drafted. National Textile Product Quality Supervision and Inspection Center, Shandong Province Fiber Inspection Bureau.
The main drafters of this standard. Wang Ying, Ren Hening, Bianai Rong, Chaiqian Hong.
This standard was first published in 1993, this is the first revision.
Standard Test Method for Elastic Textiles - Woven fabrics stretch
1 Scope
This standard specifies the method for determination of woven fabric stretched elastic.
This standard applies to woven fabrics.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 3291.3 textile material properties and test - Part 3. General
GB/T 3923.1 Textiles Tensile properties of fabrics - Part 1. breaking force and elongation Strip method
GB 6529 textiles conditioning and testing - Standard atmospheres
3 Terms and Definitions
Terms and definitions GB/T 3291.3 established in applicable to this standard.
Principle 4
Fabric stretched constant elongation or anyone, resulting in deformation, after a predetermined time to release a tensile force to respond in a predetermined time measured
Residual elongation, elastic recovery rate calculated accordingly and plastic deformation rate in order to characterize the tensile elastic fabric.
5 instruments and appliances
5.1 constant elongation (CRE) tester. shall comply with GB/T 3923.1 requirements to meet the 1% of the indicated value of the force; and can be specified elongation, fixed
Tensile strength, and has a recording apparatus.
5.2 appliance crop sample.
6 Sampling
6.1 sampling should be representative, make sure to a