HOME   Cart(0)   Quotation   About-Us Tax PDFs Standard-List Powered by Google www.ChineseStandard.net Database: 189759 (29 Sep 2024)

YY/T 0286.4-2020 PDF in English


YY/T 0286.4-2020 (YY/T0286.4-2020, YYT 0286.4-2020, YYT0286.4-2020)
Standard IDContents [version]USDSTEP2[PDF] delivered inName of Chinese StandardStatus
YY/T 0286.4-2020English260 Add to Cart 0-9 seconds. Auto-delivery. Special infusion sets -- Part 4: Infusion sets for single use with pressure infusion apparatus Valid
YY 0286.4-2006English150 Add to Cart 0-9 seconds. Auto-delivery. Special infusion sets - Part 4: Single-use infusion equipment for use with pressure infusion apparatus Obsolete
Standards related to (historical): YY/T 0286.4-2020
PDF Preview

YY/T 0286.4-2020: PDF in English (YYT 0286.4-2020)

YY/T 0286.4-2020 YY PHARMACEUTICAL INDUSTRY STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 11.040.20 C 31 Replacing YY 0286.4-2006 Special infusion sets - Part 4: Infusion sets for single use with pressure infusion apparatus (ISO 8536-8:2015, Infusion equipment for medical use - Part 8: Infusion sets for single use with pressure infusion apparatus, MOD) ISSUED ON: JUNE 30, 2020 IMPLEMENTED ON: JUNE 01, 2021 Issued by: National Medical Products Administration Table of Contents Foreword ... 3 Introduction ... 5 1 Scope ... 6 2 Normative references ... 6 3 Terms and definitions ... 6 4 General requirements ... 7 5 Materials ... 11 6 Physical requirements ... 11 7 Chemical requirements ... 13 8 Biological requirements ... 13 9 Packaging ... 13 10 Labels ... 13 11 Disposal ... 14 Appendix A (Normative) Physical test ... 16 Appendix B (Normative) Storage volume ... 17 Appendix C (Informative) Technical differences between this Part and ISO 8536- 8:2015 and reasons ... 20 References ... 22 Special infusion sets - Part 4: Infusion sets for single use with pressure infusion apparatus 1 Scope This Part of the "Specialized infusion sets" series of standards specifies the requirements for sterile supplied disposable infusion sets (hereinafter referred to as "infusion sets"), for infusion equipment which has a pressure of 200 kPa and below. This Part applies to disposable infusion sets of infusion equipment, which has a pressure of 200 kPa and below. 2 Normative references The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard. GB/T 1962.2 Conical fittings with a 6% (Luer) taper for syringes, needles and certain other medical equipment - Part 2: Lock fittings (GB/T 1962.2-2001, ISO 594-2:1998, IDT) GB 8368 Infusion sets for single use, gravity feed (GB 8368-2005, ISO 8536- 4:2004, MOD) YY/T 0466.1 Medical devices - Symbols to be used with medical device labels, labelling and information to be supplied - Part 1: General requirements (YY/T 0466.1-2016, ISO 15223-1:2012, IDT) 3 Terms and definitions The following terms and definitions apply to this document. 3.1 Filling volume VF The pipeline is full filled under gravity, whilst the pipeline remains pressure-free. Note: The filling volume is equal to the calculated volume of the pipeline. 3.2 Bolus volume VB The increased volume of the pipeline volume after pressurization (VS), as compared with the pipeline volume without pressure (VF). Note: See Figure 1 for a graphic representation of bolus volume. 3.3 Storage volume VS The volume of the pipeline under pressure, which is the sum of the filling volume (VF) and the bolus volume (VB). VS = VF + VB 4 General requirements 4.1 The names of the infusion set assembly and the separate air intake assembly are as shown in Figure 2, Figure 3, Figure 4. These illustrations represent the structure of the infusion set and air intake device. Other structures may be used, as long as the same effect can be achieved. The infusion set as shown in Figure 3 is suitable for use in bag- type plastic containers. The infusion set shown in Figure 3, which has the separate air inlet device as shown in Figure 4, OR the infusion set shown in Figure 2, is suitable for rigid containers. 4.2 The infusion set shall have a protective sheath, to keep the inside of the infusion set sterile before use. The cork piercer or needle of the gas inlet device shall have a protective sheath. When testing according to A.3.2 and A.3.4, there shall be no air or water leakage. When testing according to A.3.3, no air shall enter. 6.4 Male conical joint The male conical joint shall comply with the requirements of GB/T 1962.2. 6.5 Injection piece The injection piece shall be able to inject into the pipeline. When testing according to A.4, water leakage shall not exceed one drop. The injection piece shall be located at the accessory of male conical joint. 6.6 Liquid filter GB 8368 is applicable. 6.7 Infusion flow rate GB 8368 is applicable. 6.8 Bottle cork piercer GB 8368 is applicable. 6.9 Air intake devices GB 8368 is applicable. 6.10 Burette and dropper GB 8368 is applicable. 6.11 Pipeline Pipelines made of flexible materials shall be transparent or sufficiently transparent, so that the interface between water and air can be distinguished with normal or corrected vision, when air bubbles pass through. The length of the pipeline, from the end to the dropper (including the injection piece (if any) and the male conical joint), shall be not less than 1500 mm. 6.12 Flow regulator GB 8368 is applicable. 6.13 Protective sheath GB 8368 is applicable. f) Expiration date (year and month), appended with appropriate text, OR using graphic symbols consistent with YY/T 0466.1; g) Indication that the infusion set is for one-time use only, OR equivalent words, OR use of graphic symbols that comply with YY/T 0466.1; h) Instructions for use, including warnings, such as about the protective sheath falling off (the instructions for use can also be in the form of inserts); i) The liquid storage volume is marked according to B.3. If supporting pressure infusion equipment is specified, the manufacturer shall give the name and type of pressure infusion equipment; j) The letter "p" indicating pressure shall be larger than the surrounding text; k) Instructions that 20 drops or 60 drops of distilled water, which is dropped from the burette, are equal to (1 ± 0.1) mL or (1 ± 0.1) g. If the single packaging area is too small to give all information and/or symbols, the information can be simplified to e) and f). In this case, the information required by this Article shall be given on the next larger shelf or on the label of the multi-unit packaging. 10.3 Shelf or multi-unit packaging The shelf or multi-unit packaging shall have at least the following information: a) Manufacturer’s name and address; b) Text describing the contents; c) The batch number, which starts with the word "LOT", or uses of the graphic symbol specified in YY/T 0466.1; d) Expiration date (year and month), appended with appropriate text, or use of graphic symbols consistent with YY/T 0466.1; e) Instructions for use, including warnings, such as regarding the protective sheath falling off (the instructions for use may also be in the form of inserts); f) The letter "p" indicating pressure shall be larger than the surrounding text; g) Storage requirements. 11 Disposal Information on the safe and environmentally sound disposal of disposable infusion sets shall be given, in the accompanying documentation. Appendix A (Normative) Physical test A.1 Particulate contamination test GB 8368 is applicable. A.2 Connection strength test The tested infusion set is subjected to an axial static tension force of 15 N for 15 s. Verify whether the infusion set can withstand the applied force. A.3 Leakage test A.3.1 At the beginning of the test, condition the entire system at the test temperature. A.3.2 Connect the infusion set to the air source. Seal all other ports. Fill the infusion set with 50 kPa air pressure, at (40 ± 1) °C for 15 seconds. Place the infusion set in water. Check whether there is any air leakage. A.3.3 Fill the infusion set with water. Seal each port. Connect it to a vacuum device. Vacuum to -20 kPa at (40 ± 1) °C. Maintain it for 15 seconds. Check whether there is air entering the infusion set. If the infusion set has a flow element, this test is only applicable to the part above the flow element of the infusion set; if there is no flow element, this test is applicable to the entire infusion set. A.3.4 Apply a pressure of 200 kPa to the flow element of the infusion set and the water- filled part below, in an environment of (40 ± 1) °C, for 15 minutes. If supporting pressure infusion equipment is specified, the maximum working pressure of the pressure infusion equipment shall be applied. Note: If the infusion set has no flow element, under the same environment, check the entire pipeline under the dropper. A.4 Injection piece test The test is carried out according to the provisions of GB 8368, BUT under the internal pressure of 200 kPa. A.5 Filtration rate test of chemical liquid filter GB 8368 is applicable. ......
 
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.