HOME   Cart(0)   Quotation   About-Us Tax PDFs Standard-List Powered by Google www.ChineseStandard.net Database: 189760 (30 Nov 2024)

QC/T 764-2006 (QC/T 764-2015 Newer Version) PDF English


QC/T 764-2006 (QC/T764-2006, QCT 764-2006, QCT764-2006)
Standard IDContents [version]USDSTEP2[PDF] delivered inName of Chinese StandardStatus
QC/T 764-2015English150 Add to Cart 0-9 seconds. Auto-delivery. Road vehicles. Hydraulic braking system. Simple flare pipes, tube tapped holes, male fittings and hose end fittings Valid
QC/T 764-2006English140 Add to Cart 0-9 seconds. Auto-delivery. Department of automobile hydraulic brake metal tube, inside and outside the threaded pipe joints and hose end fittings Obsolete
Newer version: QC/T 764-2015     Standards related to (historical): QC/T 764-2015
PDF Preview

QC/T 764-2006: PDF in English (QCT 764-2006)

QC/T 764-2006 (renamed from GB 11611-89) NATIONAL AUTOMOTIVE INDUSTRY STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA UDC 629.113-592: 621.643.4 T 24 QC/T 764-2006 Renamed from GB 11611-89 Motor Vehicle -Hydraulic Braking Systems – Pipes, Tapped Holes Male Fittings and Hose End Fittings ISSUED ON: AUGUST 28, 1989 IMPLEMENTED ON: MARCH 01, 1990 Issued by: State Bureau of Technology Supervision Table of Contents 1 Subject Contents and Applicable Scope ... 3 2 Normative Reference ... 3 3 Metallic Tube ... 3 4 Taper Sealed Pipe Threaded Hole ... 5 5 Male Threaded Pipe Fittings ... 7 6 Hose End Fittings ... 8 Additional Information: ... 9 Motor Vehicle - Hydraulic Braking Systems - Pipes, Tapped Holes Male Fittings and Hose End Fittings 1 Subject Contents and Applicable Scope This Standard specifies the basic size, performance and material requirements for the metallic tube, female and male thread pipe fittings and hose end fittings used in the hydraulic braking system of the motor vehicles. This Standard is applicable to the motor vehicle equipped with hydraulic braking system. 2 Normative Reference GB 2423.17 Basic Environmental Testing Procedures for Electric and Electronic Products Test Ka: Salt Mist 3 Metallic Tube 3.1 Non-flared metallic tube Double-layer coiled tube. The basic size, burst pressure and mass per meter shall conform to the provisions of Table 1. The metallic tube may also be coated with a plastic coating on its outer surface; but it shall meet the use requirements of female and male thread pipe fittings and hose end fittings stipulated in this Standard. Table 1 mm Outer diameter D1 Without surface treatment Wall thickness Outer diameter of pipe D1 (with surface treatment) Burst pressure Mass Basic size Limit deviation Basic size Limit deviation 3.3 Material performance of metallic tube It shall conform to the provisions of Table 3. Table 3 NOTE 1): Used for the metallic tube that has not been straightened. 2): Flat furnace steel or top-blown oxygen converter steel. 3.4 Technical requirements The inner and outer surfaces of the metallic tube shall be free of the scale; the outer surface shall be corrosion resistant and can be resistant to the salt spray test for a duration of no less than 96h. The test method shall conform to the provisions of GB 2423.17. 4 Taper Sealed Pipe Threaded Hole The type and size of the taper sealed pipe threaded hole shall conform to the provisions of Figure 3 and Table 4. Material Mechanical properties Steel Tensile strength Yield point Elongation at break Rockwell hardness ......
 
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.