GB/T 5267.4-2009 PDF in English
GB/T 5267.4-2009 (GB/T5267.4-2009, GBT 5267.4-2009, GBT5267.4-2009)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 5267.4-2009 | English | 110 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Passivation of corrosion-resistant stainless-steel fasteners
| Valid |
Standards related to (historical): GB/T 5267.4-2009
PDF Preview
GB/T 5267.4-2009: PDF in English (GBT 5267.4-2009) GB/T 5267.4-2009
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 21.060.10
J 13
GB/T 5267.4-2009 / ISO 16048:2003
Passivation of corrosion-resistant stainless-steel
fasteners
(ISO 16048:2003, IDT)
ISSUED ON: OCTOBER 15, 2009
IMPLEMENTED ON: MARCH 01, 2010
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of the People's Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Passivation ... 5
5 Verification of passivation ... 6
Annex A (informative) Passivity ... 7
Foreword
This Part is one of the series of national standards "Fastener surface treatment".
The series includes:
a) GB/T 5267.1-2002, Fasteners - Electroplated Coatings;
b) GB/T 5267.2-2002, Fasteners - Non-electrolytically applied zinc flake
coatings;
c) GB/T 5267.3-2002, Fasteners - Hot dip galvanized coatings;
d) GB/T 5267.4-2002, Passivation of corrosion-resistant stainless-steel
fasteners.
This Part is Part 4 of GB/T 5267.
This Part identically adopts the international standard ISO 16048:2003
"Passivation of corrosion-resistant stainless-steel fasteners" (English version).
In the normative references, use Chinese standards to replace international
standards (Chapter 2).
Annex A of this Part is informative.
This Part was proposed by China Machinery Industry Federation.
This Part shall be under the jurisdiction of National Technical Committee on
Fasteners of Standardization Administration of China (SAC/TC 85).
Main drafting organizations of this Part: China Machinery Productivity
Promotion Center.
This Part is explained by the Secretariat of National Technical Committee on
Fasteners of Standardization Administration of China.
Passivation of corrosion-resistant stainless-steel
fasteners
1 Scope
This Part of GB/T 5267 specifies the methods most often used for passivation
of corrosion-resistant stainless-steel fasteners.
Typical anodic dissolution behaviour of an active-passive-transpassive metal is
given in Annex A.
2 Normative references
The provisions in following documents become the provisions of this Standard
through reference in this Part of GB/T 5267. For dated references, the
subsequent amendments (excluding corrigendum) or revisions do not apply to
this Standard, however, parties who reach an agreement based on this
Standard are encouraged to study if the latest versions of these documents are
applicable. For undated references, the latest edition of the referenced
document applies.
GB/T 3098.6, Mechanical Properties of fasteners- Stainless steel bolts,
screws and studs (GB/T 3098.6-2000, idt ISO 3506-1:1997)
GB/T 3098.15, Mechanical properties of fasteners-Nuts made of stainless-
steel (GB/T 3098.15-2000, idt ISO 3506-2:1997)
GB/T 3098.16, Mechanical properties of fasteners - Stainless steel set
screws (GB/T 3098.16-2000, idt ISO 3506-3:1997)
GB/T 3098.21, Mechanical properties of fasteners - Stainless steel tapping
screws (GB/T 3098.21-2008, ISO 3506-4:2003, Mechanical procedure
corrosion-resistant stainless-steel fasteners - Part 4: Tapping screws, IDT)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1 passivation
chemical treatment that increases the thickness of the naturally occurring
chromium rich oxide film present on all types of stainless-steel surfaces
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|