GB/T 41758.2-2022 PDF English
Search result: GB/T 41758.2-2022_English: PDF (GB/T41758.2-2022)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 41758.2-2022 | English | 230 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Plastics -- Polyketone (PK) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
| Valid |
BUY with any currencies (Euro, JPY, GBP, KRW etc.): GB/T 41758.2-2022 Related standards: GB/T 41758.2-2022
PDF Preview: GB/T 41758.2-2022
GB/T 41758.2-2022: PDF in English (GBT 41758.2-2022) GB/T 41758.2-2022
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 83.080.20
CCS G 31
Plastics - Polyketone (PK) moulding and extrusion materials
- Part 2: Preparation of test specimens and determination of
properties
(ISO 21970-2:2019, MOD)
ISSUED ON: OCTOBER 12, 2022
IMPLEMENTED ON: OCTOBER 12, 2022
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of China.
Table of Contents
Foreword ... 3
Introduction ... 7
1 Scope ... 8
2 Normative references ... 8
3 Terms and definitions ... 11
4 Preparation of test specimens ... 11
5 Conditioning of test specimens ... 12
6 Determination of properties ... 12
References ... 15
Foreword
This document was drafted in accordance with the rules given in GB/T 1.1-2020,
Directives for standardization - Part 1: Rules for the structure and drafting of
standardizing documents.
This document is Part 2 of GB/T 41758 Plastics - Polyketone (PK) moulding and
extrusion materials. The following parts have been released for GB/T 41758:
-- Part 1: Designation system and basis for specifications
-- Part 2: Preparation of test specimens and determination of properties.
This document is modified from ISO 21970-2:2019 Plastics - Polyketone (PK)
moulding and extrusion materials - Part 2: Preparation of test specimens and
determination of properties.
The technical differences between this document and ISO 21970-2:2019 and the
reasons are as follows:
-- Use the normatively referenced GB/T 41758.1 to replace ISO 21970-1 (see
Chapter 1), to adapt to the technical conditions in China;
-- Use the normatively referenced GB/T 17037.1 to replace ISO 294-1 (see 4.3), to
adapt to the technical conditions in China;
-- Use the normatively referenced GB/T 2918 to replace ISO 291 (see Chapter 5), to
adapt to the technical conditions in China;
-- Use the normatively referenced GB/T 19467.1 to replace ISO 10350-1 (see
Chapter 6), to adapt to the technical conditions in China;
-- Use the normatively referenced GB 2536 to replace IEC 60296 (see Table 2), to
adapt to the technical conditions in China;
-- Use the normatively referenced GB/T 3682.1 to replace ISO 1133-1 (see Table 2),
to adapt to the technical conditions in China;
-- Use the normatively referenced GB/T 37426 to replace ISO 20753 (see Table 2),
to adapt to the technical conditions in China;
-- Use the normatively referenced GB/T 1033.1 to replace ISO 1183-1 (see Table 2),
to adapt to the technical conditions in China;
-- Use the normatively referenced GB/T 1033.2 to replace ISO 1183-2 (see Table 2),
to adapt to the technical conditions in China;
Plastics - Polyketone (PK) moulding and extrusion materials
- Part 2: Preparation of test specimens and determination of
properties
1 Scope
This document describes the preparation of test specimens and test methods for the
determination of properties of polyketone moulding and extrusion materials. It specifies
requirements for the handling of the test material and/or the conditioning of the test
material before moulding and the test specimens before testing.
The determination method of properties is selected from the general test methods in
GB/T 19467.1. This document also lists other test methods widely used or of special
significance for moulding and extrusion materials, as well as the determination methods
for characteristic properties in GB/T 41758.1.
In order to ensure that the test results are reproducible and repeatable, it is necessary to
use the methods for preparation of test specimens and state conditioning specified in
this document, as well as the specified specimen size and test method. Test data
obtained using specimens prepared under different conditions or using specimens of
different dimensions may not be consistent.
2 Normative references
The following documents are normatively referenced in this document and are
indispensable for its application. For dated references, only the version corresponding
to that date is applicable to this document; for undated references, the latest version
(including all amendments) is applicable to this document.
GB/T 1033.1, Plastics - Methods for determining the density of non-cellular plastics
- Part 1: Immersion method liquid pyknometer method and titration method (GB/T
1033.1-2008, ISO 1183-1:2004, IDT)
GB/T 1033.2, Plastics - Methods for determining the density of non-cellular plastics
- Part 2: Density gradient column method (GB/T 1033.2-2010, ISO 1183-2:2004,
MOD)
GB/T 1033.3, Plastics - Methods for determining the density of non-cellular plastics
- Part 3: Gas pyknometer method (GB/T 1033.3-2010, ISO 1183-3:1999, IDT)
GB/T 9345.4, Plastics - Determination of ash - Part 4: Polyamides (GB/T 9345.4-
2008, ISO 3451-4:1998, IDT)
GB/T 12006.2, Plastics - Polyamides - Part 2: Determination of water content (GB/T
12006.2-2009, ISO 15512:1999, MOD)
GB/T 16422.1, Plastics - Methods of exposure to laboratory light sources - Part 1:
General guidance (GB/T 16422.1-2019, ISO 4892-1:2016, IDT)
GB/T 16422.2, Plastics - Methods of exposure to laboratory light sources - Part 2:
Xenon-arc lamps (GB/T 16422.2-2014, ISO 4892-2:2006, IDT)
GB/T 16422.3, Plastics - Methods of exposure to laboratory light sources - Part 3:
Fluorescent UV lamps (GB/T 16422.3-2014, ISO 4892-3:2006, IDT)
GB/T 16422.4, Plastics - Methods of exposure to laboratory light sources - Part 4:
Open-flame carbon-arc lamps (GB/T 16422.4-2014, ISO 4892-4:2004, IDT)
GB/T 17037.1, Plastics - Injection moulding of test specimens of thermoplastic
materials - Part 1: General principles, and moulding of multipurpose and bar test
specimens (GB/T 17037.1-2019, ISO 294-1:2017, MOD)
GB/T 19466.2, Plastics - Differential scanning calorimetry (DSC) - Part 2:
Determination of glass transition temperature (GB/T 19466.2-2004, ISO 11357-
2:1999, IDT)
GB/T 19466.3, Plastics - Differential scanning calorimetry (DSC) - Part 3:
Determination of temperature and enthalpy of melting and crystalliation (GB/T
19466.3-2004, ISO 11357-3:1999, IDT)
GB/T 19467.1, Plastics - Acquisition and presentation of comparable single-point
data - Part 1: Moulding materials (GB/T 19467.1-2004, ISO 10350-1:1998, MOD)
GB/T 31838.2, Solid insulating materials - Dielectric and resistive properties - Part
2: Resistive properties (DC methods) - Volume resistance and volume resistivity
(GB/T 31838.2-2019, IEC 62631-3-1:2016, IDT)
GB/T 31838.3, Solid insulating materials - Dielectric and resistive properties - Part
3: Resistive properties (DC methods) - Surface resistance and surface resistivity
(GB/T 31838.3-2019, IEC 62631-3-2:2015, IDT)
GB/T 31838.6, Solid insulating materials - Dielectric and resistive properties - Part
6: Dielectric properties (AC method) - Relative permittivity and dielectric
dissipation factor (frequencies 0.1 Hz ~ 10 MHz) (GB/T 31838.6-2021, IEC 62631-
2-1:2018, IDT)
GB/T 36800.2, Plastics - Thermomechanical analysis (TMA) - Part 2: Determination
of coefficient of linear thermal expansion and glass transition temperature (GB/T
36800.2-2018, ISO 11359-2:1999, IDT)
GB/T 37426, Plastics - Test specimens (GB/T 37426-2019, ISO 20753:2018, MOD)
GB/T 41758.1, Plastics - Polyketone (PK) moulding and extrusion materials - Part
1: Designation system and basis for specifications (GB/T 41758.1-2022, ISO 21970-
1:2019, MOD)
ISO 6603-2, Plastics - Determination of puncture impact behaviour of rigid plastics
- Part 2: Instrumented impact testing
3 Terms and definitions
No terms and definitions need to be defined in this document.
4 Preparation of test specimens
4.1 General
It is essential to prepare the test specimens using the same procedure (injection
moulding) and the same processing conditions.
4.2 Pretreatment of materials before moulding
Before processing, the moisture content of the material after drying shall not exceed
0.2%. If the moisture content exceeds this limit, the material shall be dried to a moisture
content below the limit in accordance with the manufacturer’s instructions.
4.3 Injection moulding
Use the conditions specified in Table 1 to prepare injection molding test specimens in
accordance with GB/T 17037.1.
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|