GB/T 33514-2017 PDF English
Search result: GB/T 33514-2017
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 33514-2017 | English | 120 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Steel cord conveyor belts -- Determination of the lateral and vertical displacement of steel cords
| Valid |
PDF Preview: GB/T 33514-2017
GB/T 33514-2017: PDF in English (GBT 33514-2017) GB/T 33514-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 53.040.20
G 42
Steel Cord Conveyor Belts -
Determination of the Lateral and
Vertical Displacement of Steel Cords
ISSUED ON. FEBRUARY 28, 2017
IMPLEMENTED ON. SEPTEMBER 01, 2017
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Method A. Measurement of Steel Rope Spacing and Enhanced Belt Width . 4
3 Method B. Measurement of Vertical Displacement of Steel Rope against the
Average Height of Rope ... 6
4 Test Report ... 8
Bibliography ... 9
Steel Cord Conveyor Belts -
Determination of the Lateral and
Vertical Displacement of Steel Cords
1 Scope
This Standard specifies the method for determining the average lateral displacement
of steel cord in the steel cord conveyor belt, and the vertical displacement relative to
the average height of the rope in GB/T 28267.1 [1].
This Standard is applicable to the steel cord conveyor belts.
2 Method A. Measurement of Steel Rope Spacing and
Enhanced Belt Width
2.1 Instrument
NOTE. If there is a similar or more accurate instrument, it can also be used.
2.1.1 Band tape with scale of 1.0mm.
2.1.2 Hand-held optical magnifying glass with a scale of 0.1mm, and the magnification
is no less than 8×.
2.1.3 Dial gauge with a scale of 0.1mm.
2.1.4 The flat horizontal surface used for placing the full-width conveyor belt.
2.2 Specimen
The specimen shall be of full width and no-less-than-50mm length of the belt. The
cutting edge shall be smooth and free of dirt; the steel rope shall be clearly exposed.
If the cutting edge is not very smooth, the specimen can be prepared in a different
manner; so that ensure accurate measurement of the rope position in accordance with
this Standard.
2.3 Test Procedures
2.3.3 Measurement of pitch in the selected area (see Figure 2)
Optionally select 21 pieces of consecutive and adjacent steel ropes from the specimen.
Use dial gauge (2.1.3) or hand-held optical magnifying glass (2.1.2) to measure the
distance of every two adjacent steel ropes among the 21 pieces of steel ropes; and
record their values as t1, t2, ... t20.
NOTE. If the pitch cannot be measured with naked eye in the selected area; use the above
magnifying glass to enlarge the pitch (maximum 20×) for accurate measurement.
Figure 2 – Schematic Diagram for Measuring the Steel Rope Spacing within the
Selected Area
3 Method B. Measurement of Vertical Displacement of
Steel Rope against the Average Height of Rope
NOTE. This test is only carried out under the condition that the conveyor belt has at least one
side with the uniformly-thick covering layer. Because the outer surface of the covering layer
with uniform thickness is the reference for measuring the height of the rope. Different references
may affect the accuracy of the test.
3.1 Instrument
NOTE. If there is a similar or more accurate instrument, it can also be used.
3.1.1 Dial gauge described in 2.1.3.
3.1.2 Hand-held optical magnifying glass described in 2.1.2.
3.1.3 Horizontal surface described in 2.1.4.
3.2 Specimen
Table 1 – Evaluation on Rope Height Difference
Figure 4 – Schematic Diagram for Measuring the Height of Steel Rope
4 Test Report
The test report shall include the following contents.
a) Mention of performing the test as per this Standard;
b) Mark of steel cord conveyor belt for test;
c) Average pitch (tm);
d) Deviation rate for enhanced belt width;
e) Deviation from single pitch to the average pitch;
f) Values of percentage of Δh1, Δh2, and Δh3;
g) Test date.
Total number of steel
ropes in specimen
The number of steel ropes The number of steel ropes The number of steel ropes
and
Qty. Qty. Qty. Percentage Percentage Percentage
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|