GB/T 2912.2-2009 PDF in English
GB/T 2912.2-2009 (GB/T2912.2-2009, GBT 2912.2-2009, GBT2912.2-2009)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 2912.2-2009 | English | 85 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Textiles -- Determination of formaldehyde -- Part 2: Released formaldehyde (vapour absorption method)
| Valid |
| GB/T 2912.2-1998 | English | 279 |
Add to Cart
|
3 days
|
Textiles--Determination of formaldehyde--Part 2: Released formaldehyde (Vapour absorption method)
| Obsolete |
Standards related to (historical): GB/T 2912.2-2009
PDF Preview
GB/T 2912.2-2009: PDF in English (GBT 2912.2-2009) GB/T 2912.2-2009
GB
ICS 59.080.01
W 04
NATIONAL STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
Replacing GB/T 2912.2-1998
Textiles - Determination of Formaldehyde -
Part 2. Released Formaldehyde (Vapour
Absorption Method)
(ISO 14184-2. 1998, MOD)
ISSUED ON. JUNE 11, 2009
IMPLEMENTED ON. JANUARY 1, 2010
Jointly Issued by. General Administration of Quality Supervision,
Inspection and Quarantine (AQSIQ);
Standardization Administration of China (SAC) of the
People's Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative References ... 5
3 Principle ... 5
4 Reagents ... 6
5 Apparatus ... 6
6 Preparation of Formaldehyde Standard Solution and Calibration ... 7
7 Sample Preparation ... 8
8 Operation Procedures ... 9
9 Calculation and Expression Mode of Results ... 9
10 Test Report ... 10
Appendix A (Normative) Standardization of Formaldehyde Stock Solution – . 11
Sodium Sulfite Method ... 11
Appendix B (Normative) Standardization of Formaldehyde Stock Solution – 13
Iodometry ... 13
Appendix C (Informative) Operation Procedure of Using Chromotropic Acid to
Replace Acetylacetone Reagent ... 16
Appendix D (Informative) Information on Accuracy of the Test ... 18
Corrigendum... 19
Foreword
GB/T 2912 "Textile - Determination of formaldehyde" is divided into 3 parts.
- Part 1. Free and hydrolyzed formaldehyde (water extraction method);
- Part 2. Released formaldehyde (vapour absorption method);
- Part 3. High performance liquid chromatography method.
This Part is Part 2 of GB/T 2912.
Adopting re-drafting method, this Part modifies and adopts ISO 14184-2.1998
"Textiles-Determination of Formaldehyde - Part 2. Released Formaldehyde (Vapour
Absorption Method)" (English edition).
Compared with ISO 14184-2.1998, the differences of this Part are as follows.
- Add detection limit in the Scope;
- Add GB/T 11415 in the Normative References;
- Add the detailed descriptions in principle;
- Add requirements that the calculation results shall be rounded off to integers;
- Add Appendix B “Standardization of formaldehyde stock solution – Iodometry”.
This Part replaces GB/T 2912.2-1998 "Textiles - Determination of Formaldehyde -
Part 2. Released Formaldehyde (Vapour Absorption Method)".
Compared with GB/T 2912.2-1998, the main changes of this Part are as follows.
- Add detection limit in the Scope;
- Add the detailed descriptions in principle;
- Add "The average value of 2 inspection results shall be taken as the test result.
The calculation result shall be rounded off to integral number";
- In Chapter 9, add "If the result is less than 20 mg/kg, test result shall be reported
as 'not detectable";
- Add Appendix B “Standardization of formaldehyde stock solution – Iodometry”.
Appendix A and Appendix B of this Part are normative Appendix C and Appendix D
are informative.
Textiles - Determination of Formaldehyde -
Part 2. Released Formaldehyde (Vapour Absorption
Method)
Warning. The personnel using this Part of GB/T 2912 shall have practical
experiences in regular laboratory work. This Part does not point out all the
possible safety problems. Users have the responsibility to take appropriate
safety and health measures and also ensure meeting the conditions specified in
relevant regulations of the State.
1 Scope
This Part of GB/T 2912 specifies a method for determining the amount of
formaldehyde released under the conditions of accelerated storage from textiles in
any form by means of a vapour absorption method.
This Part is intended for use in the range of releasable formaldehyde on the fabric
between 20 mg/kg and 3500 mg/kg. The detection limit is 20 mg/kg. Below this limit
the result is reported as "not-detectable".
2 Normative References
The following documents contain provisions which, through reference in this Part of
GB/T 2912, constitute provisions of this Part. For dated reference, subsequent
amendments (excluding corrections) or revisions of these publications do not apply.
However, parties who enter into agreements based on this Part are encouraged to
investigate the possibility of applying the most recent editions of the standards
indicated below. For any undated references, the latest edition of the document
referred to applies.
GB/T 6529 Textiles - Standard Atmospheres for Conditioning and Testing (GB/T
6529-2008, ISO 139. 2005, MOD)
GB/T 6682 Water for Analytical Laboratory Use - Specification and Test Methods
(GB/T 6682-2008, ISO 3696. 1987, MOD)
3 Principle
A weighed fabric specimen is suspended over water in a sealed jar. The jar is placed
in an incubator at a controlled temperature for a specified length of time. The released
Where,
F - the formaldehyde content in fabric sample, mg/kg;
c - the formaldehyde content in sample solution as read from the calibration curve,
μg/mL;
m – mass of test specimen, g.
The average value of 2 parallel tests shall be taken as the test result. The calculation
result shall be rounded off to integral number.
If the result is less than 20 mg/kg, the test result shall be reported as 'not-detectable'.
10 Test Report
Test report shall include the following contents.
a) The standards used;
b) The date the sample was received, the means in which it was stored prior to test
and the date tested;
c) Description of the specimen tested and how it is packaged;
d) The mass of the test specimens and, if required, the correction coefficient for the
mass;
e) Range of working curve;
f) The amount of formaldehyde extracted from the specimen, mg/kg;
g) Any deviation, by agreement or otherwise, from the procedure specified.
Appendix B
(Normative)
Standardization of Formaldehyde Stock Solution –
Iodometry
B.1 General
The stock solution containing approximately 1500μg/mL formaldehyde shall be
accurately standardized in order to prepare a precise working curve for use in
colorimetric analysis.
B.2 Principle
An aliquot of the stock solution is reacted with an excess of iodine solution. Use
standard acid solution, with thymolphthalein as indicator, to carry out the back-titration.
B.3 Apparatus
B.3.1 5 mL, 10 mL, 20 mL, 50 mL one-mark pipette.
B.3.2 50 mL burette.
B.3.3 250 mL iodine flask and conical flask with stopper.
B.3.4 500 mL, 1L volumetric flask.
B.4 Reagents
B.4.1 Iodine solution [c(I2)=0.1 mol/L]. put 13 g of iodine (I2) and 30 g of potassium
iodide (KI) into a 1 L brown volumetric flask. Dilute to the mark with water. Shake well
and store in the dark place.
B.4.2 Sodium hydroxide. c(NaOH)=1 mol/L.
B.4.3 Sulfuric acid. c(H2SO4)=0.5 mol/L.
B.4.4 Starch indicator. dissolve 0.5g of soluble starch into 100mL water. Boil for 2
min. Prepare it before use.
B.4.5 Sodium thiosulfate solution [c(Na2S2O3)=0.1 mol/L]. weigh 25 g of
Na2S2O3·5H2O (or 16 g of anhydrous Na2S2O3). Dissolve it into 1L of water that has
Appendix C
(Informative)
Operation Procedure of Using Chromotropic Acid to Replace
Acetylacetone Reagent
C.1 Reagents
C.1.1 Chromotropic acid, 50 g/L, freshly made aqueous solution and, if necessary,
filtered before use.
Note. This reagent is supplied as a sodium salt for formaldehyde determination. Considerable
variations are evident in its quality and a new calibration curve shall be prepared for each new
batch purchased. Solutions older than 12 h shall be discarded.
C.1.2 Concentrated sulfuric acid, (density 1.84 g/L) of analytical reagent quality.
C.1.3 Sulfuric acid, [c (H2SO4)=7.5 mol/L]. Concentrated sulfuric acid (C.1.2) (750 g,
405 mL) is added carefully into water. Allowed to cool down. Use water to dilute to 1 L.
Cool down before use.
C.2 Operation procedure
C.2.1 Transfer integer multiples of 1.0 mL of solution (8.1) into a test tube.
Respectively add 4.0 mL of 7.5 mol/L sulfuric acid (C.1.3), 1.0 mL of 50 g/L
chromotropic acid solution (C.1.1), and 5.0 mL of concentrated sulfuric acid (C.1.2).
Mix the solution in test tube thoroughly after each addition. After at least 2 min, add
the next reagent.
C.2.2 Place the tube vertically in a boiling water bath (the liquid level of water bath
shall be above that of the solution in the tube) for (30 ± 1) min. After cooling, transfer
the solution to a 50 mL...
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|