GB/T 21655.1-2008 (GB/T 21655.1-2023 Newer Version) PDF English
GB/T 21655.1-2008 (GB/T21655.1-2008, GBT 21655.1-2008, GBT21655.1-2008)
Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
GB/T 21655.1-2023 | English | 140 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Textiles -- Evaluation of absorption and quick-drying -- Part 1: Method for combination tests
| Valid |
GB/T 21655.1-2008 | English | 70 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Textiles -- Evaluation of absorption and quick-drying -- Part 1: Method for combination tests
| Obsolete |
Newer version: GB/T 21655.1-2023 Standards related to (historical): GB/T 21655.1-2023
GB/T 21655.1-2008: PDF in English (GBT 21655.1-2008) GB/T 21655.1-2008
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 59.080.30
W 04
Textiles - Evaluation of absorption and quick-drying -
Part 1. Method for combination tests
ISSUED ON. APRIL 29, 2008
IMPLEMENTED ON. DECEMBER 1, 2008
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration Committee.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Principle... 5
5 Equipment, materials and reagents ... 5
6 Standard atmosphere for moisture control and testing ... 6
7 Sampling and sample preparation ... 6
8 Test procedures ... 6
9 Technical requirements and evaluation for absorption and quick-drying .. 10
10 Test report ... 11
Textiles - Evaluation of absorption and quick-drying -
Part 1. Method for combination tests
1 Scope
This Part of GB/T 21655 specifies the test methods and evaluation indicators
for combination of single test indicator of absorption and quick-drying of textiles.
This Part is applicable to all kinds of textiles and their products.
2 Normative references
The following standards contain the provisions which, through reference in this
Part, constitute the provisions of this Part. For dated references, subsequent
amendments (excluding corrections) or revisions do not apply to this Part.
However, the parties who enter into agreement based on this Part are
encouraged to investigate whether the latest versions of these documents are
applicable. For undated reference documents, the latest versions apply to this
Part.
GB 6529, STANDARD atmospheres for textiles conditioning and testing (neq
GB 6529-1986, ISO 139.1973)
GB/T 6682, Water for analytical laboratory use - Specification and test
methods (neq GB/T 6682-1992, ISO 3696.1987)
GB/T 8629, Textiles - Domestic washing and drying procedures for textile
testing (eqv GB/T 8629-2001, ISO 6330.2000)
GB/T 12740, Types and basic parameters of cars for monocable circulating
aerial ropeway
FZ/T 01071, Textiles - Test method for capillary effect
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply to
this Part of GB/T 21655.
3.1 water absorption rate
the percentage of water absorbed by the sample to the original mass of the
sample when the sample is completely immersed in water and then is taken out
5.7 Timer. division of 0.1 s.
6 Standard atmosphere for moisture control and
testing
6.1 The atmosphere for moisture control and testing uses the standard
atmosphere specified in GB 6529.
6.2 Samples shall be in a state of moisture balance in the relaxed state before
the test. Moisturizing method and requirements are according to GB 6529.
General moisture control needs more than 16h, synthetic fiber samples ask for
at least 2h. Samples with a nominal moisture regain rate of 0 do not require
moisture control.
7 Sampling and sample preparation
7.1 The method and quantity of sample collection are based on product
standards or agreed by all parties involved. Cut a full fabric of 0.5 m or more
into each sample. Avoid more than 2m from the ends when sampling. Textile
products require at least 1 unit.
7.2 Cut each sample into two pieces (one for pre-wash test and one for post-
wash test). One of them is washed 5 times according to the 5A procedure of
GB/T 8629, or washed according to the methods and times agreed by all parties
concerned. Drying process is according to oven drying method.
7.3 Cut sample. The number and size of samples shall meet the requirements
of Clause 8. When sample is cut, it shall be evenly arranged in the area more
than 150 mm away from the cloth edge. Each sample is not in the same
longitudinal and lateral position. If the product consists of different fabrics, the
sample shall be selected from the main fabric and avoid defects and wrinkles
that affect the test results.
8 Test procedures
8.1 Water absorption rate
8.1.1 Cut 5 specimens for each sample. The size of each specimen is at least
10cm x 10cm. The specimen shall be flat without wrinkles.
8.1.2 Place the specimen under standard atmospheric conditions to adjust the
humidity and balance.
8.1.3 Weigh the original mass of the specimen, to the nearest of 0.001g.
...... Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|