HOME   Cart(0)   Quotation   About-Us Tax PDFs Standard-List Powered by Google www.ChineseStandard.net Database: 189759 (3 Nov 2024)

GB/T 18147.3-2015 PDF in English


GB/T 18147.3-2015 (GB/T18147.3-2015, GBT 18147.3-2015, GBT18147.3-2015)
Standard IDContents [version]USDSTEP2[PDF] delivered inName of Chinese StandardStatus
GB/T 18147.3-2015English100 Add to Cart 0-9 seconds. Auto-delivery. Test method for hemp fiber -- Part 3: Test method for length of hemp fiber Valid
GB/T 18147.3-2000English199 Add to Cart 2 days Test method for hemp fibre. Part 3: Test method for length of hemp fibre Obsolete
Standards related to (historical): GB/T 18147.3-2015
PDF Preview

GB/T 18147.3-2015: PDF in English (GBT 18147.3-2015)

GB/T 18147.3-2015 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 59.060.10 B 32 Replacing GB/T 18147.3-2000 Test method for hemp fiber - Part 3: Test method for length of hemp fiber ISSUED ON: JULY 03, 2015 IMPLEMENTED ON: OCTOBER 01, 2015 Issued by: General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People’s Republic of China. Table of Contents Foreword ... 3  1 Scope ... 5  2 Normative references ... 5  3 Terms and definitions ... 5  4 Principle ... 6  5 Instruments and tools ... 6  6 Test conditions ... 6  7 Sampling ... 6  8 Conditioning ... 6  9 Test steps ... 6  10 Experimental calculation ... 8  11 Test report ... 9  Test method for hemp fiber - Part 3: Test method for length of hemp fiber 1 Scope This Part of GB/T 18147 specifies the test method for length of hemp fiber. This Part applies to raw white hemp sliver and cotton type hemp fiber. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies to this document. For undated references, the latest edition (including any amendment) applies to this document. GB/T 8170, Rules of rounding off for numerical values & expression and judgment of limiting values GB/T 9995, Determination of moisture content and moisture regain of textile - Oven- drying method GB/T 18146.2, Hemp fiber - Part 2: Raw white hemp sliver GB/T 18146.3, Hemp fiber - Part 3: Cotton type hemp fiber 3 Terms and definitions The following terms and definitions are applicable to this document. 3.1 Average length The average value obtained by weighting the mass of each group of fibers which are measured in groups by length. 3.2 Short fiber content The percentage of the mass of short fibers shorter than a certain length limit in the hemp fiber TO the total fiber mass. respectively, so that the fibers become relatively straight bundle which is neat at one end. 9.1.2 Lay the samples, from long to short in a straight line, evenly and straightly on the glass plate (bottom-lined with black clearer) from left to right; during the arrangement process, use a coir scrub brush to arrange for several times, and use tweezers to pick up hemp grains, hard strips, etc. The free fibers brushed off shall be re-classified into the sample after arrangement. 9.1.3 Use tweezers to arrange the fibers into a hemp bundle with a neat end and a width of 15 mm, with the long fibers on the bottom and the short fibers on the top. 9.1.4 Again, spread the fibers evenly and straightly on the glass plate along a straight line, and divide them into five groups from long to short. Use tweezers to fold each group to form a small bundle, with the long fiber on the bottom and the short fiber on the top, whose width is approximately 10 mm ~ 15 mm; use a pressure hammer or glass sheet to press it. 9.2 Testing 9.2.1 Method A - Length measurement by comb sorter (applicable to slivers) 9.2.1.1 Arrange the sorted straight fiber bundles on the top of the lower comb piece of the comb sorter group by group, with the neat end flush with the first comb piece; use a pressing fork to press the fibers straightly into the lower comb piece. 9.2.1.2 Press the upper comb piece into the lower comb piece. 9.2.1.3 Use a clip to extract the fibers from the longest end of the fibers, by as small amount as possible and as many times as possible, so as to avoid taking out short fibers. 9.2.1.4 Twist the extracted fibers into small strands by groups and place them in a metal box or a black clearer in sequence. After each extraction of a group, put down a lower comb piece, until each group of fibers is extracted. 9.2.1.5 Starting from the shortest group, weigh the mass of each group of fibers on the balance in turn, and record it. 9.2.2 Method B - Manual grouping and weighing method 9.2.2.1 Press out a straight-line trace on the black clearer; hold the neat end of the neatly arranged straight fiber bundle; fold the other end into a pen tip; use a clip to extract the fibers from long to short; arrange the fibers evenly on the black clearer along the straight line from left to right, where the fibers are required to be straight and parallel; use a measuring scale to measure the length of the fibers. 9.2.2.2 Regulations for grouping of fiber length: ......
 
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.