HOME   Cart(1)   Quotation   About-Us Tax PDFs Standard-List
Powered by Google-Search & Google-Books www.ChineseStandard.net Database: 189759 (26 Jun 2022)

GB/T 14172-2009 (GB/T14172-2009)

Standard IDContents [version]USDSTEP2[PDF] delivered inName of Chinese StandardStatus
GB/T 14172-2009English70 Add to Cart 0--3 minutes. Auto-delivery. Static roll stability test method for motor vehicles Obsolete


GB/T 14172-2009: PDF in English (GBT 14172-2009)
GB/T 14172-2009
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 43.020
T 04
Replacing GB/T 14172-1993
Static roll stability test method for motor vehicles
ISSUED ON: MARCH 23, 2009
IMPLEMENTED ON: JANUARY 01, 2010
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3 
1 Scope ... 4 
2 Normative references ... 4 
3 Terms and definitions ... 4 
4 Measuring instruments and equipment ... 5 
5 Test conditions ... 6 
6 Test methods ... 6 
7 Processing of data ... 7 
8 Test records ... 7 
Appendix A (Informative) Test records ... 8 
Foreword ... 3 
1 Scope ... 4 
2 Normative references ... 4 
3 Terms and definitions ... 4 
4 Measuring instruments and equipment ... 5 
5 Test conditions ... 6 
6 Test methods ... 6 
7 Processing of data ... 7 
8 Test records ... 7 
Appendix A (Informative) Test records ... 8 
Static roll stability test method for motor vehicles
1 Scope
This standard specifies the test method for the static roll stability of motor
vehicles.
This standard applies to motor vehicles. Combination vehicles may make
reference to it.
2 Normative references
The provisions in following documents become the provisions of this standard
through reference in this standard. For the dated references, the subsequent
amendments (excluding corrections) or revisions do not apply to this standard;
however, parties who reach an agreement based on this standard are
encouraged to study if the latest versions of these documents are applicable.
For undated references, the latest edition of the referenced document applies.
GB/T 1184 Geometrical tolerancing - Geometrical tolerance for features
without individual tolerance indications (GB/T 1184-1996, eqv ISO 2768-2:
1989)
3 Terms and definitions
The following terms and definitions apply to this standard.
3.1
Static rollover stability
The motor vehicle’s inherent resistance to rollover when subjected to lateral
forces under static conditions.
3.2
Roll angle
When the motor vehicle rolls together with the roll test bench, the angle
between the supporting plane of the motor vehicle’s wheels and the
horizontal plane.
reaches the critical roll state.
5 Test conditions
5.1 Technical conditions of motor vehicles
5.1.1 The assemblies, components and auxiliary equipment of motor vehicles
(including on-board tools and spare tires) must be fully equipped according to
the exit-factory technical conditions. They shall be installed in the specified
position. If the position is adjustable (such as lifting shaft, adjustable air
suspension), it shall be adjusted to a state which is appropriate to the load.
5.1.2 The tire’s pressure shall be in accordance with the technical requirements
of the motor vehicle. The error shall not exceed 10 kPa.
5.1.3 In order to prevent leakage of fuel, lubricating oil, coolant, it may use the
method of blockage or equivalent mass substitution.
5.1.4 For motor vehicles which adopt air suspension and oil-gas suspension, it
shall install the safety device to prevent the suspension from coming off. For
those which have a height-adjustment mechanism, it shall lock the mechanism.
5.1.5 It shall, according to the measurement requirements, determine the load
state of the motor vehicle (if there is no special requirement, based on the curb
mass state). Where it requires installing simulated load on the motor vehicle, all
loads shall be appropriately positioned, to avoid displacement during the roll
test of motor vehicles.
5.2 Environmental conditions
The ambient wind speed is not more than 1.5 m/s.
6 Test methods
6.1 Determination of max stable roll angle of motor vehicle when it rolls
leftwards
6.1.1 Place the motor vehicle on the roll test bench. Allow the wheel to be in a
straight-line driving state. The longitudinally symmetrical plane of the motor
vehicle is parallel to the center line of the test bench.
6.1.2 Apply the parking brake. Install anti-slip stop and the anti-rollover safety
equipment.
6.1.3 Start the test bench, so that the motor vehicle is tilted leftwards together
with the test bench at an appropriate speed (when the roll angle is more than
......
 
(Above excerpt was released on 2019-05-11, modified on 2021-06-07, translated/reviewed by: Wayne Zheng et al.)
Source: https://www.chinesestandard.net/PDF.aspx/GBT14172-2009