QB/T 2472-2000 PDF English
US$150.00 · In stock · Download in 9 secondsQB/T 2472-2000: Agricultural Flexible PVC Calendering and Stentering Film Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| QB/T 2472-2000 | English | 150 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Agricultural Flexible PVC Calendering and Stentering Film
| |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: QB/T 2472-2000
QB/T 2472-2000: Agricultural Flexible PVC Calendering and Stentering Film---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/QBT2472-2000
QB
LIGHT INDUSTRY STANDARD OF
THE PEOPLE’S REPUBLIC OF CHINA
Classification number: G33
Filing number: 6916-2000
Agricultural flexible PVC calendering and stentering
film
ISSUED ON: MARCH 30, 2000
IMPLEMENTED ON: AUGUST 01, 2000
Issued by: State Light Industry Administration
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Product classification ... 4
4 Requirements ... 5
5 Test method ... 6
6 Inspection rules ... 11
7 Marking, packaging, transportation and storage ... 13
Agricultural flexible PVC calendering and stentering
film
1 Scope
This standard specifies the product classification, requirements, test methods,
inspection rules and markings, packaging, transportation, storage of agricultural
flexible PVC calendering and stentering film.
This standard applies to agricultural flexible PVC calendering and stentering
film (hereinafter referred to as "films") that are mainly made of polyvinyl chloride
resin, added with plasticizers, stabilizers and other auxiliaries, produced by the
calendering and stentering method.
2 Normative references
The clauses contained in the following standards constitute the clauses of this
standard by being quoted in this standard. At the time of publication, the editions
indicated were valid. All standards will be revised, and all parties using this
standard shall explore the possibility of using the latest version of the following
standards.
GB/T 2828-1987 Sampling procedures and tables for lot-by-lot inspection by
attributes (Apply to inspection of successive lots or batches)
GB/T 2918-1998 Plastics - Standard atmospheres for conditioning and
testing
GB/T 6673-1986 Plastics - Film and sheeting - Determination of length and
width
GB/T 13022-1991 Plastics - Test method for tensile properties
QB/T 1130-1991 Plastics angle tear performance test method
HG 2-163-1965 Low-temperature elongation test method for plastics
3 Product classification
3.1 The classification of the film is as shown in Table 1.
5.1.1 The sample must be randomly selected from each delivery batch of film.
Remove the three surface layers (about 2 m) from the film roll. Cut the specimen.
Indicate the longitudinal direction of the film.
5.1.2 The thickness and width shall be taken as specified in Table 6. One roll
shall be subject to visual inspection and the other roll shall be subject to the
testing of physical and mechanical properties and drip-free performance.
5.2 Thickness
As shown in Figure 1, cut the specimen into three pieces for thickness testing.
Divide it into 5 points averagely along the width direction, to measure the
thickness. Use a 0.001 mm gauge; the difference between the maximum or
minimum value and the nominal thickness of the 15 measurement points is
used as the thickness limit deviation.
Remove 3 maximum values and 3 minimum values from the recorded 15 points
of measurement value. Take the arithmetic average of the thickness of the
remaining 9 points as the average thickness of the film. Calculate the difference
between the thickness and the average thickness.
The allowable range of the difference between the thickness and the average
thickness is calculated according to formula (1).
Where:
d - Allowable range of the difference between the thickness and the average
thickness, %;
- The average thickness, mm;
d1 - Maximum measured value of 9 points, mm;
d2 - Minimum measured value of 9 points, mm.
5.3 Width and length
It is performed according to the provisions of GB/T 6673.
5.4 Appearance
Visually inspect under natural light and measure with corresponding measuring
tools.
It is performed according to the provisions of QB/T 1130.
5.5.6 Heating loss rate
Cut out three specimens of 40 mm x 60 mm as shown in Figure 2. Put them in
a desiccator containing anhydrous calcium chloride (or silica gel) for 4 hours.
Take them out and weigh them to the nearest 0.0001 g. Then put them in a (100
± 2) °C non-blasted oven for 6 hours. The specimen is suspended at 2/3 of the
height of the oven and is on the same level as the mercury bulb of the
thermometer. The distance between the specimen and the mercury bulb is not
more than 80 mm. The distance between the specimens is not less than 30 mm.
After taking it out of the oven, put it in a desiccator to cool to room temperature
before weighing.
The heating loss rate is calculated according to formula (2).
Where:
n - Heating loss rate, %;
m0 - The mass of the specimen before heating, g;
m - The mass of the specimen after heating, g.
Calculate the arithmetic mean of the test results of the three specimens and
retain it to the first decimal place.
5.5.7 Water extract
Cut out three specimens of 50 mm x 100 mm as shown in Figure 2. Place them
in a desiccator containing anhydrous calcium chloride (or silica gel) for 4 hours.
Take them out and weigh them to the nearest 0.0001 g. Then put it into distilled
water at a constant temperature of (50 ± 2) °C for 24 h. All specimens shall be
immersed in water and they shall not be attached to each other or attached to
the container wall. Different specimens shall not be tested in the same container.
Take out the specimen. Put it between two pieces of filter paper to absorb it dry.
Then put it in a (50 ± 2) °C oven for 8 h. Put it in a desiccator containing
anhydrous calcium chloride (or silica gel) to cool to room temperature. Weigh it,
accurate to 0.0001 g.
The water extract is calculated according to formula (3).
Films are inspected on a batch basis. The films less than 50 t which are
continuously produced by the same raw materials, the same formula, the same
process, the same specification form a batch.
6.2 Sampling
Use the random sampling method.
The specifications and appearance are in accordance with GB/T 2828. It uses
the normal inspection sub-sampling plan. The general inspection level is II and
the acceptance quality level (AQL) is 6.5, as shown in Table 6.
6.3 Inspection classification
6.3.1 Exit-factory inspection
The exit-factory inspection items are all items except water extract, heating loss
rate and drip-free performance of drip-free film within 6 months of use.
6.3.2 Type inspection
Perform inspections in accordance with all technical requirements specified in
this standard. During normal production, at least once every three months;
when one of the conditions occur, type inspection shall also be carried out.
a) During normal production, if major changes in raw materials and
processes may affect product performance;
b) When the production is resumed after long term suspension;
c) When the new product is type-finalized, or the old product is transferring
plant for production;
d) When the relevant inspection results of the exit-factory inspection and the
last type inspection are significantly different;
e) When the national quality supervision agency requests for type inspection.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of QB/T 2472-2000 be delivered?Answer: The full copy PDF of English version of QB/T 2472-2000 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of QB/T 2472-2000_English with my colleagues?Answer: Yes. The purchased PDF of QB/T 2472-2000_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- QB/T 2472-2000 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of QB/T 2472-2000?A step-by-step guide to download PDF of QB/T 2472-2000_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "QB/T 2472-2000".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|