GB/T 3098.15-2023 PDF English
US$470.00 · In stock · Download in 9 secondsGB/T 3098.15-2023: Mechanical properties of fasteners - Stainless steel nuts Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 3098.15: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 3098.15-2023 | English | 470 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Mechanical properties of fasteners - Stainless steel nuts
| Valid |
| GB/T 3098.15-2014 | English | 125 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Mechanical properties of fasteners Nuts made of stainless-steel
| Obsolete |
| GB/T 3098.15-2000 | English | 679 |
Add to Cart
|
3 days
|
Mechanical properties of fasteners stainless nut
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 3098.15-2023
GB/T 3098.15-2023: Mechanical properties of fasteners - Stainless steel nuts---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3098.15-2023
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 21.060.20
CCS J 13
Replacing GB/T 3098.15-2014
Mechanical properties of fasteners - Stainless steel nuts
(ISO 3506-2.2020, Fasteners - Mechanical properties of corrosion-resistant stainless
steel fasteners - Part 2.Nuts with specified grades and property classes, MOD)
Issued on. MAY 23, 2023
Implemented on. DECEMBER 01, 2023
Issued by. State Administration for Market Regulation;
National Standardization Administration.
Table of Contents
Foreword... 3
Introduction... 8
1 Scope... 11
2 Normative references... 12
3 Terms and definitions... 13
4 Symbols... 14
5 Marking system... 15
5.1 Nut type marking... 15
5.2 Stainless steel group and performance grade marking system... 15
6 Design of bolt and nut connection pairs... 17
7 Materials... 18
7.1 Chemical composition... 18
7.2 Heat treatment of martensitic stainless steel nuts... 20
7.3 Surface finishing... 20
7.4 Corrosion resistance... 20
8 Mechanical and physical properties... 21
9 Inspection... 26
9.1 Manufacturer's inspection... 26
9.2 Supplier's inspection... 26
9.3 Buyer's inspection... 27
9.4 Delivery of test results... 27
10 Test method... 27
10.1 Proof load test... 27
10.2 Hardness test... 31
11 Nut marking and labeling... 33
11.1 Marking... 33
11.2 Manufacturer's identification mark... 34
11.3 Nut marking... 35
11.4 Packaging marking (label)... 37
Appendix A (Informative) Design principles for stainless steel nuts... 38
Appendix B (Normative) Thread size of proof load test mandrel... 41
References... 43
Foreword
This document was drafted in accordance with the provisions of GB/T 1.1-2020
"Directives for standardization - Part 1.Rules for the structure and drafting of
standardizing documents".
This document is Part 15 of GB/T 3098 "Mechanical properties of fasteners". GB/T
3098 has published the following parts.
- GB/T 3098.1 Mechanical properties of fasteners - Bolts, screws and studs;
- GB/T 3098.2 Mechanical properties of fasteners - Nuts;
- GB/T 3098.3 Mechanical properties of fasteners - Set screws;
- GB/T 3098.5 Mechanical properties of fasteners - Tapping screws;
- GB/T 3098.6 Mechanical properties of corrosion-resistant stainless-steel fasteners
- Part 1.Bolts, screws and studs;
- GB/T 3098.7 Mechanical properties of fasteners - Thread rolling screws;
- GB/T 3098.8 Mechanical properties of fasteners - Parts for bolted connections for
use at temperatures from -200 °C ~ +700 °C;
- GB/T 3098.9 Mechanical properties of fasteners - Prevailing torque type steel nuts;
- GB/T 3098.10 Mechanical properties of fasteners - Bolts, screws, studs and nuts
made of non-ferrous metals;
- GB/T 3098.11 Mechanical properties of fasteners - Drilling screws with taping
screw thread;
- GB/T 3098.12 Mechanical properties of fasteners - Cone proof load test on nuts;
- GB/T 3098.13 Mechanical properties of fasteners - Torsional test and minimum
torques for bolts and screws with nominal diameters 1 mm to 10 mm;
- GB/T 3098.14 Mechanical properties of fasteners - Widening test on nuts;
- GB/T 3098.15 Mechanical properties of fasteners - Nuts made of stainless-steel;
- GB/T 3098.16 Mechanical properties of fasteners - Set screws made of stainless-
steel;
- GB/T 3098.17 Mechanical properties of fasteners - Preloading test for the detection
of hydrogen embrittlement - Parallel bearing surface method;
- GB/T 3098.18 Mechanical properties of fasteners - Blind rivets testing;
- GB/T 3098.19 Mechanical properties of fasteners - Blind rivets with break pull
mandrel;
- GB/T 3098.20 Mechanical properties of fasteners - Wing nuts with specified proof
torque;
- GB/T 3098.21 Mechanical properties of fasteners - Part 21.Tapping screws of
stainless-steel;
- GB/T 3098.22 Mechanical properties of fasteners made of the fine grain non-heat
treatment steel - Bolts, screws and studs.
- GB/T 3098.23 Mechanical properties of fasteners - M42 ~ M72 bolts, screws and
studs;
- GB/T 3098.24 Mechanical properties of fasteners - Stainless steel and nickel alloys
bolts, screws, studs and nuts for high temperature applications;
- GB/T 3098.25 Mechanical properties of fasteners - Guidance for the selection of
stainless steels and nickel alloys for fasteners;
- GB/T 3098.26 Mechanical properties of fasteners - Flat washers.
This document replaces GB/T 3098.15-2014 "Mechanical properties of fasteners - Nuts
made of stainless-steel". Compared with GB/T 3098.15-2014, in addition to structural
adjustments and editorial changes, the main technical changes are as follows.
a) ADD the nut type information (see 5.1);
b) ADD the duplex (austenite-ferrite) stainless steel with performance levels of 70,
80, 100 (see Figure 1);
c) ADD the austenitic stainless steel performance level 100 and group A8 (see Figure
1);
d) ADD the design of stainless steel bolt and nut assemblies (see Chapter 6) and the
design principles of stainless steel nuts (see Appendix A);
e) CHANGE the surface finishing (see 7.3; 4.3 of the 2014 edition);
f) ADD the calculated value of the nut proof load and the principle of numerical
rounding (see Tables 5 ~ 8);
g) ADD the inspection procedure requirements and guidance (see Chapter 9);
h) ADD the thread size requirements for the mandrel of the nut proof load test (see
Appendix B);
i) CHANGE the proof load and hardness test methods (see Chapter 10; Chapter 7 of
the 2014 edition);
j) CHANGE the nut marking and labeling, adding the marking method for thin nuts
with reduced load capacity (see Chapter 11; 4.2 of the 2014 edition);
k) DELETE the common appendixes in the series of standards for mechanical
properties of stainless steel fasteners (see Appendix A ~ Appendix E of the 2014
edition).
This document modifies and adopts ISO 3506-2.2020 "Fasteners - Mechanical
properties of corrosion-resistant stainless steel fasteners - Part 2.Nuts of specified
groups and performance levels".
Compared with ISO 3506-2.2020, this document has made the following structural
adjustments.
- 10.2.2.1, 10.2.2.2, 10.2.2.3 correspond to 10.2.2 in ISO 3506-2.2020;
- ADD Figure 4; Figure 5 corresponds to Figure 4 in ISO 3506-2.2020, Figure 6
corresponds to Figure 5 in ISO 3506-2.2020, Figure 7 corresponds to Figure 6 in
ISO 3506-2.2020, Figure 8 corresponds to Figure 7 in ISO 3506-2.2020, Figure 9
corresponds to Figure 8 in ISO 3506-2.2020.
The technical differences between this document and ISO 3506-2.2020 and their
reasons are as follows.
- USE the normative reference GB/T 3098.25 to replace ISO 3506-6, to adapt to
China's technical conditions (see 7.1);
- USE the normative reference GB/T 39310 to replace ISO 16228, to adapt to China's
technical conditions (see 9.4);
- USE the normative reference GB/T 16825.1 to replace ISO 7500-1, to adapt to
China's technical conditions (see 10.1.3);
- USE the normative reference GB/T 228.1 to replace ISO 6892-1, to adapt to China's
technical conditions (see 10.1.5);
- USE the normative reference GB/T 3098.1 to replace ISO 898-1, to adapt to China's
technical conditions (see 10.1.6);
- USE the normative reference GB/T 4340.1 to replace ISO 6507-1, to adapt to
China's technical conditions (see 10.2.2.1);
- USE the normative reference GB/T 230.1 to replace ISO 6508-1, to adapt to China's
technical conditions (see 10.2.2.1);
- USE the normative reference GB/T 231.1 to replace ISO 6506-1, to adapt to China's
technical conditions (see 10.2.2.1);
- USE the normative reference GB/T 3099.4 to replace ISO 1891-4, to adapt to
China's technical conditions (see 11.4);
- DELETE the "soft" state of austenitic stainless steel performance grade 70 fasteners,
to meet the processing state of austenitic stainless steel fasteners (see Figure 1).
This document has made the following editorial changes.
- CHANGE the standard name to "Mechanical properties of fasteners - Stainless
steel nuts";
- USE the Chinese documents to replace the normative reference international
documents;
- CHANGE that "Stainless steel group marking (Part 1) consists of one letter..." to
"Stainless steel group marking (Part 1) consists of one letter and one digit..." (see
5.2.2);
- CHANGE the maximum and minimum values of the fixture apertures
corresponding to M5 and M6 after calculation according to tolerance grade D11
(see Table 9).
Please note that some contents of this document may involve patents. The issuing
agency of this document does not assume the responsibility for identifying patents.
This document was proposed by the China Machinery Industry Federation.
This document shall be under the jurisdiction of the National Technical Committee for
Standardization of Fasteners (SAC/TC 85).
Drafting organizations of this document. China Machinery Productivity Promotion
Center Co., Ltd., Shanghai Jiyoubiaowu High Strength Fastener Co., Ltd., Fu'an
Aozhan Industrial Co., Ltd., Hebei Wuwei Avionics Technology Co., Ltd., Wuxi
Standard Parts Factory Co., Ltd., and the Quality Supervision and Inspection Center for
General Parts of the Machinery Industry.
This document is interpreted by the National Technical Committee for Standardization
of Fasteners.
The previous versions of this document and the documents it replaces are as follows.
- This document was first published in 1986 as GB/T 3098.15-1986.It was revised
for the first time in 2000.It was revised for the second time in 2014;
- This is the third revision.
1 Scope
This document specifies the mechanical and physical properties of coarse and fine
thread nuts made of corrosion-resistant stainless steel, when tested at an ambient
temperature of 10 °C ~ 35 °C. The performance grades corresponding to the austenitic,
martensitic, ferritic and duplex (austenitic-ferritic) stainless steel nut groups are
specified.
2 Normative references
The contents of the following documents constitute the essential terms of this document
through normative references in the text. Among them, for dated references, only the
version corresponding to that date applies to this document; for undated references, the
latest version (including all amendments) applies to this document.
3 Terms and definitions
The following terms and definitions apply to this document.
4 Symbols
The following symbols apply to this document.
5 Marking system
The stainless steel group marking (Part 1) consists of a letter and a digit, wherein the
letter specifies the stainless steel category.
6 Design of bolt and nut connection pairs
The combination of performance grades of nuts and bolts, screws and studs shall be as
specified in Table 1.
7 Materials
Unless otherwise specified, nuts conforming to this document shall be cleaned and
polished.
To prevent corrosion, nuts should be used with bolts, screws, studs, washers of the same
stainless steel group (e.g., A2 nuts with A2 bolts). Other combinations may be used
(e.g., A4 nuts with D4 bolts), provided that.
8 Mechanical and physical properties
Whether during the manufacturing process or at the final product inspection, nuts of
specified stainless steel groups and performance grades shall meet the proof load and
hardness requirements specified in Tables 3 ~ 8, when tested at ambient temperatures
of 10 °C ~ 35 °C according to the methods specified in Chapter 10.
9 Inspection
The supplier may choose its own method (regularly evaluate the manufacturer, verify
the test results provided by the manufacturer, test the actual nuts, etc.), to control and/or
test the nuts provided by the manufacturer, to ensure that they meet the chemical
composition, mechanical and physical property requirements specified in Chapters 7
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 3098.15-2023 be delivered?Answer: The full copy PDF of English version of GB/T 3098.15-2023 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 3098.15-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3098.15-2023_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3098.15-2023 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 3098.15-2023?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3098.15-2023 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 3098.15-2023?A step-by-step guide to download PDF of GB/T 3098.15-2023_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 3098.15-2023".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|