GB/T 19392-2013 PDF English
US$175.00 · In stock · Download in 9 secondsGB/T 19392-2013: General specification for in-vehicle satellite navigation equipment Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 19392: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 19392-2013 | English | 175 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
General specification for in-vehicle satellite navigation equipment
| Valid |
| GB/T 19392-2003 | English | 879 |
Add to Cart
|
6 days
|
General specification of car GPS navigation system
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 19392-2013
GB/T 19392-2013: General specification for in-vehicle satellite navigation equipment---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT19392-2013
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 33.200
M 50
Replacing GB/T 19392-2003
General specification for in-vehicle
satellite navigation equipment
Issued on. DECEMBER 31, 2013
Implemented on. JULY 15, 2014
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine of the PRC;
Standardization Administration of the PRC.
Table of Contents
Foreword... 3
1 Scope... 5
2 Normative references... 5
3 Terms and definitions... 7
4 Requirements... 9
5 Test methods... 19
6 Quality assessment procedures... 27
7 Marking, packaging, transport, and storage... 33
8 Instructions for use... 34
Appendix A (Normative) Classification of product non-conformity... 35
1 Scope
This Standard specifies the requirements, test methods, inspection rules,
marking, packaging, transport, and storage of in-vehicle satellite navigation
equipment (hereafter referred to as equipment).
This Standard applies to the development and production of in-vehicle satellite
navigation equipment. Other in-vehicle electronic products which combine
wireless communication and satellite navigation and have route navigation
function can refer for use.
2 Normative references
The following documents are indispensable for the application of this document.
For the dated references, only the editions with the dates indicated are
applicable to this document. For the undated references, the latest edition
(including all the amendments) are applicable to this document.
GB/T 191 Packaging - Pictorial Marking for Handling of Goods
GB/T 2423.1 Environmental testing - Part 2.Test methods - Tests A. Cold
GB/T 2423.2 Environmental testing - Part 2.Test methods - Tests B. Dry heat
GB/T 2423.3 Environmental testing - Part 2.Testing method - Test Cab.
Damp heat, steady state
GB/T 2423.5 Environmental testing for electric and electronic products - Part
2.Test methods - Test Ea and guidance. Shock
GB/T 2423.10 Environmental testing for electric and electronic products -
Part 2.Tests methods - Test Fc. Vibration (sinusoidal)
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1.
Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot
inspection
3 Terms and definitions
The following terms and definitions apply to this document.
3.1 In-vehicle satellite navigation equipment
The equipment, which is based on satellite positioning, combines with other
positioning means to obtain vehicle position data, and matches with the map
database for navigation to obtain vehicle position data and guide in real time.
3.2 Map database for navigation
A database of digital map information stored in a specific format and associated
with navigation information. The information related to the map usually includes
geocoding data, route planning data, background data, and reference data, etc.
3.3 Positioning module
A functional module which is based on satellite positioning information and can
incorporate the output information of other sensors to determine the vehicle
position.
3.4 Map matching
A technique for matching the position (track) acquired from the positioning
module with the map information provided by the map database for navigation
to determine the position of the vehicle on the map.
3.5 Route planning
The process of using information such as the road network provided by the map
database for navigation to help the driver plan the route.
4 Requirements
4.1 General
4.1.1 Equipment composition
4.1.1.1 The equipment composition shall include at least the following devices
or equipment units.
4.1.1.2 The in-vehicle satellite dynamic navigation equipment shall at least
include a receiving device for real-time traffic information.
4.1.2 Basic functions
4.1.2.1 It shall have at least the following basic functions.
4.1.2.2 The in-vehicle satellite dynamic navigation equipment shall also have
the function of receiving, analyzing, and processing real-time traffic information.
4.1.3 Software design
The following requirements shall be met.
4.1.4 Display
The following requirements shall be met.
4.1.5 Voice output
The following requirements shall be met.
4.1.8 Appearance quality
The surface shall be free of defects such as dents, scratches, cracks,
deformation, rust, mildew stain, and overflow of the infusion. The coating
(plating) layer shall not be foamed, cracked, or peeled off. The text symbols and
markings shall be clear and beautiful.
4.1.9 Boundary dimensions, mass, and installation
Boundary dimensions, mass, and installation methods are specified by product
standards, but the installation of the equipment shall not affect the driver’s safe
driving.
4.2 Performance and function requirements
4.2.1 Performance
4.2.2 Functions
4.2.2.1 Vehicle positioning and map matching functions
It shall have the following vehicle positioning and map matching functions.
a) It shall have a reckoning navigation function, to enable the vehicle to
navigate when the satellite navigation positioning system signal is blocked;
b) Provide other functions with the map matching vehicle position; and
provide status information for the road, position, etc. where the vehicle is
located.
4.2.2.3 Target search functions
The following target search functions shall be provided.
4.2.2.4 Route planning functions
It shall have the following route planning functions.
4.2.2.5 Route guidance functions
When the vehicle drives along the planned route, according to the position of
the vehicle on the route, guidance information and prompt information shall be
provided.
4.2.3 Power supply and power consumption
4.2.3.1 Power supply
It shall be specified by product standards.
4.2.3.2 Power consumption
It shall be specified by product standards.
4.2.4 Interfaces
4.3 Environmental adaptability
4.3.1 Dry heat work
The equipment, at a temperature of 70 °C, shall be able to work normally.
4.3.2 Dry heat storage
Equipment shall be able to withstand dry heat storage tests at 85 °C.
5 Test methods
5.1 Test conditions
5.1.1 Unless otherwise specified, all tests shall be carried out under test
standard atmospheric conditions as follows.
5.1.2 The test site shall be selected in a place with convenient transportation,
no significant electromagnetic signal interference around, and no obstacles
above 10° of the circumferential elevating angle.
5.2 General requirements
5.2.1 Overview
For the requirements in Clause 4, if the specific test methods are not specified
in this clause, it can be done by visual inspection, drawing, text, object check,
operation demonstration, or according to the method specified in the product
standard.
5.2.2 Appearance quality
USE visual inspection and hand-feeling to check; or USE a magnifying glass
with a magnification of not more than 10.
5.2.3 Boundary dimensions, mass, and installation
USE measuring tool and weighing apparatus to check the dimensions and
mass. USE review method to inspect the installation requirements.
5.3 Performance and functions
5.3.1 Positioning accuracy
The positioning accuracy of the satellite positioning device selected by the
equipment is tested according to the method specified in the product standard.
The positioning accuracy of the equipment is tested as follows.
5.3.3 Start-up time
USE a stopwatch to measure the start-up time of the equipment.
5.3.4 Efficiency
The test procedure is as follows.
5.3.7 Interfaces
5.3.7.1 Data communication interface
The equipment’s data communication interface is, according to the product
standard, connected to the corresponding communication equipment, to check
the data content and format.
6 Quality assessment procedures
6.1 Inspection classification
The inspection includes identification inspection and quality conformity
inspection.
6.2 Identification inspection
The purpose of identification inspection is to verify whether the equipment
meets its specifications. In one of the following cases, an identification
inspection shall be carried out.
6.2.1 Inspection items and sequence
The identification inspection items and sequence are shown in Table 5.
Depending on the circumstances, the user and the producer can negotiate to
trim the inspection items or change the inspection sequence.
6.2.2 Number of samples
2 sets~4 sets of inspection samples are randomly drawn from the identification
lot. It is also allowed to use different number of samples according to different
inspection items, as specified by product standards.
6.3 Quality conformity inspection
6.3.1 Inspection classification
The quality conformity inspection is divided into lot-by-lot inspection and
periodic inspection.
6.3.5 Lot-by-lot inspection
The purpose of lot-by-lot inspection is to judge whether the quality of each lot
submitted for inspection meets the specified requirements.
According to the inspection object, lot-by-lot inspection is divided into one-
hundred percent inspection and sampling inspection.
6.3.5.1 One-hundred percent inspection
6.3.5.2 Sampling inspection
6.3.5.2.1 Sampling scheme
From the qualified lots submitted for inspection, samples are randomly selected.
Unless otherwise specified, the sampling scheme is based on the single normal
inspection sampling scheme of general inspection level II specified in GB/T
2828.1-2012.Its acceptance quality limit (AQL) is specified as.
7 Marking, packaging, transport, and storage
7.1 Marking
Product marking shall comply with the provisions of GB/T 191 and GB/T 6388.
On the product, there shall be the following marks. trademark, enterprise name
and address, product model, date of manufacture.
7.2 Packaging
7.3 Transport
Once the product has been packaged, it can be transported by any means of
transportation. However, during transport, rain-proof, shock-proof, and safety
measures shall be taken.
7.4 Storage
The packaged equipment shall be stored in a warehouse with an ambient
temperature of 0 °C~35 °C, a relative humidity of less than 80%, and no acid or
alkali and other corrosive gases and strong magnetic fields around.
8 Instructions for use
The instructions for use (book) shall be prepared in accordance with the
provisions of GB 5296.1 and provide the following relevant information.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 19392-2013 be delivered?Answer: The full copy PDF of English version of GB/T 19392-2013 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 19392-2013_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 19392-2013_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 19392-2013 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 19392-2013?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 19392-2013 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 19392-2013?A step-by-step guide to download PDF of GB/T 19392-2013_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 19392-2013".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|